BRP SEA-DOO GTI 130 2019 Скачать руководство пользователя | Manualshive

Страница: 124 / 204

background image

MAINTENANCE SCHEDULE

Maintenance is very important for keeping the watercraft in a safe operating con-
dition. The watercraft should be serviced as per the maintenance schedule.

A repair shop or person of the owner's choosing may maintain, replace, or re-
pair emission control devices and systems. These instructions do not require
components or service by BRP or authorized Sea-Doo dealers. Although an au-
thorized Sea-Doo dealer has an in-depth technical knowledge and tools to service
the Sea-Doo personal watercraft, the emission-related warranty is not condi-
tioned on the use of an authorized Sea-Doo dealer or any other establishment
with which BRP has a commercial relationship. For emission-related warranty
claims, BRP is limiting the diagnosis and repair of emission-related parts to the
authorized Sea-Doo dealers. For more information, please refer to the

US EPA

EMISSION-RELATED WARRANTY

contained herein. Proper maintenance is the

owner’s responsibility. A warranty claim may be denied if, among other things,
the owner or operator caused the problem through improper maintenance or use.

You must follow the instructions for fuel requirements in the fueling section of
this manual. Even if gasoline containing greater than ten volume percent ethanol
is readily available, the US EPA issued a prohibition against the use of gasoline
containing greater than 10 vol% ethanol that applies to this vehicle. The use of
gasoline containing greater than 10 vol% ethanol with this engine may harm the
emission control system.

Disregard the information pertaining to the following systems if the watercraft is
not equipped with these features:

– iBR (intelligent Brake and Reverse)

Carry out all maintenance as listed in the schedule whenever the hours or time of
each column is reached.

NOTE:

As an example, at 200 hours or 2 years, complete all items in this column

and ALSO in the EVERY 100 hours or 1 year column.

WARNING

Failure to properly maintain the watercraft according to the maintenance
schedule and procedures can make it unsafe to operate.

The maintenance schedule does not exempt the pre-ride inspection.

AFTER EACH RIDE IN SALT OR DIRT WATER

Rinse engine compartment with fresh water and drain salt water

Flush the exhaust system

EVERY MONTH IN SALT OR DIRT WATER

Spray an anticorrosion lubricant to metallic components in engine compartment (every
10 hours in salt water use)

Inspect sacrificial anode

122

______________

https://www.boat-manuals.com/

«
...
122
123
124
125
126
...
»

Содержание SEA-DOO GTI 130 2019













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEA-DOO GTI 130 2019

Бренд: Advanced Elements Страницы: 20

Бренд: Barrus Страницы: 50

Бренд: Prestige Страницы: 120

Бренд: Supra Страницы: 92

Бренд: Supra Страницы: 88

Бренд: AFRI-CAT Страницы: 24

Бренд: SEABOB Страницы: 82

Бренд: Baitstar Страницы: 12

Бренд: S/C Yachts Страницы: 10

Бренд: J/Boats Страницы: 51

Бренд: Pelican Страницы: 2

Бренд: AKONA Страницы: 12

Бренд: Rondar Raceboats Limited Страницы: 14

Бренд: Feathercraft Страницы: 16

Бренд: Bayliner Страницы: 96

Бренд: Sea Ray Страницы: 64

Бренд: Sea Ray Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды