BROWN 2000 Series Скачать руководство пользователя страница 9

Страница: 9 / 60

Equipment Safety

Safety Decals

The following safety decals should be attached to the equipment at all times. Should any decals

become damaged or lost, it is the responsibility of the owner to replace it. Additional decals may be

obtained from the dealer or Brown Manufacturing Corporation at no charge.

Part No.: SD-010.

ADvERTENCIA

ADvERTISSEMENT

WARNINg

Antes de probar la unidad por primera vez deben

remitirse a las instrucciones contenidas en el manual.

S’assurer de bien comrendre toutes les

consignes du manuel de propriétarie avant

d’utiliser la unité.

Read and understand

owner’s manual before

operating unit.

Part No.: SD-001A.

THROWN OBJECT HAZARD

To prevent serious injury or death from

thrown objects:

•

Stay clear when blade is turning.

•

Operate only with all guards

installed and in good condition.

•

Stop operation if bystanders

come within several hundred feet.

WARNING

o prevent serious injury

or death:

•Operate only at 540 RPM PTO.

•Keep guards and shields

in place.

SD-008A, Standard models*

WARNING

To prevent serious injury

or death:

•Operate only at 1000 RPM

PTO.

•Keep guards and shields

SD-007A, Standard models*

DANGER

Содержание 2000 Series





























































Результаты поиска

Содержание 2000 Series

Отзывы:

Похожие инструкции для 2000 Series

Бренды по названию

Популярные бренды

BROWN 2000 Series, Руководство владельца/оператора

Результаты поиска

Содержание 2000 Series

Отзывы:

Похожие инструкции для 2000 Series

Бренды по названию

Популярные бренды