BROWN 2000 Series Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 60

background image

38

Blades are sold in pairs only, by weight - mount in pairs only.

Shut the unit down, see page 32 for “Safety When Working Under Cutter Deck”. Lift the cutter deck

about one foot above the ground and place jack stands or blocks on each side of the cutter deck to

support the weight of the cutter. Lower the deck to rest on the stands.

The Brown Tree Cutter uses a total of four cutting blades, all four blades are alike. It is necessary

that the blades are installed in the correct sequence. When installing new blades, alternate the

position of the cutting bevel, first one blade up, next blade bevel down. After all four blades are

installed, bevel up blades will be directly across (180 degrees) the blade bar from each other.

Replacement blades are shipped in pairs by weight, keep blades in pairs - DO NOT MIX - mount

pairs across the bar from each other.

All blades are mounted underneath the blade bar and the blade bolt is inserted from below with the

nut on top of the blade bar.

NOTE: See blade bolt tightening procedure for additional information on blade bolt torque

requirements. See Page 31 for tightening instructions.

NOTICE: IF FOR ANy REASON ONE BlADE MUST BE REplACED, ITS OppOSINg

BlADE MUST BE REplACED AT THE SAME TIME TO INSURE pROpER BAlANCE

OF THE BlADE BAR. IMpROpER BAlANCE OF THE BlADE BAR WIll CAUSE

vIBRATION AND pOSSIBlE COMpONENT FAIlURE.

Diagram denotes proper blade placement.

«
...
36
37
38
39
40
...
»

Содержание 2000 Series





























































Отзывы:

Нет отзывов

Похожие инструкции для 2000 Series

Бренд: Navman Страницы: 17

Бренд: Raytheon Страницы: 69

Бренд: Galaxy Audio Страницы: 24

Бренд: Unex Страницы: 5

Бренд: Rain-Flo Irrigation Страницы: 20

Attest Auto-reader 390

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

PELTOR WS LiteCom Plus

Бренд: 3M Страницы: 7

Steri-Vac GS Series

Бренд: 3M Страницы: 52

Бренд: IFM Страницы: 175

Бренд: IFM Страницы: 5

Бренд: Land Pride Страницы: 38

Бренд: Vatech Страницы: 137

Бренд: Vatech Страницы: 68

Бренд: Varytec Страницы: 52

Бренд: XanLite Страницы: 2

Бренд: X-Rite Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды