BROWN 2000 Series Скачать руководство пользователя страница 16

Страница: 16 / 60

WARNINg

Wear protective

clothing.

Warning!

Wear protective

clothing.

Wear close-fitting clothing and other protective

devices appropriate for the job.

Equipment Safety

Warning!

Slopes and rough

terrain.

When operating on slopes or rough terrain,

decrease travel speed. Do not operate in an area

where the tractor could roll over.

Be sure to

fasten safety belt when operating tractor!

Warning!

Roll-over protection.

Do not operate the cutter on any tractor not

equipped with a certified roll-over protective

structure (ROPS).

WARNINg

Slow travel speed when

operating on slopes or

rough terrain.

WARNINg

Use only with

tractors equipped

with a certified

roll-over protective

structure.

Danger!

Tighten blade bolts.

Blade bolts will stretch with use and

must be tightened. Follow maintenance

instructions in this manual (see page 31).

If the cutter is operated with loose blade

bolts, blades and blade carrier will be

damaged. Operation with damaged

blades and blade carrier will lead to

blade ejection and will cause serious

injury or death

Tighten blade bolts as

prescribed in owners

manual. Ejection of

blade will cause serious

injury or death.

DANGER

Содержание 2000 Series





























































Результаты поиска

Содержание 2000 Series

Отзывы:

Похожие инструкции для 2000 Series

Бренды по названию

Популярные бренды

BROWN 2000 Series, Руководство владельца/оператора

Результаты поиска

Содержание 2000 Series

Отзывы:

Похожие инструкции для 2000 Series

Бренды по названию

Популярные бренды