BROWN 2000 Series Скачать руководство пользователя страница 18

Страница: 18 / 60

Assembly

WARNINg!

The driveline shield and bell shield must be kept in good

operating condition.

Failure to maintain safety shields can result in injury and death.

Remove the two-piece bridge clamp from the clutch hub assembly. Slide the hub onto the input

shaft of the gearbox. Align the groove of the input shaft with the bolt grooves on the hub. Reinstall

the two-piece bridge clamp with the two bolts provided and tighten securely. Retorque lock bolts

every hour for the first eight hours of use.

Failure to do so will result in decreased life of the

clutch hub and gearbox shaft splines.

7. Slide aluminum bell shield and bell shield clamp over drive shaft and attach bell shield to

mounting plate with the clamp. Adjust clamp as needed to assure proper attachment.

8. Check the drive shaft for proper length:

a. Hitch the cutter to the tractor, please refer to page 21 “Attach equipment to tractor”..

b. Lift the cutter to the tractor’s maximum lift position.

c. Measure the distance from the PTO of the tractor to the input shaft of the

cutter’s gearbox.

d. Push both halves of the drive shaft together fully. Measure the overall

length.

e. If the length of the compressed drive shaft is greater than the length

between the PTO and input shaft, then the drive shaft must be shortened.

please NOTE: Equal amounts must be removed from each section of the

drive shaft.

1. Install tailwheel stem, Item D next page, into fork holder tube, Item E next page, placing collar, Item F

next page, over stem and inserting roll key, Item G next page, through collar and stem.

2. Raise A-frame from its shipping position to its operational position (almost perpendicular to the cutter

deck) . Install A-frame braces to the mounting brackets at the top of the A-frame with the provided bolts and

tighten securely, Item H next page.

3. Open Deck - Bolt the rear end of the A-frame braces to the mounting brackets near the rear of the deck

and tighten bolts securely. See Item A, next page.

3a. Folding Deck - Bolt the rear end of the braces to the inside of the outside hinge - see Item B, next page.

Assemble hydraulic hoses BEFORE the installation of drive shaft. See diagram 20-1, page 20.

4. Separate the male and female halves of the drive shaft. Apply heavy grease to the telescoping portion

of the male drive shaft. Recouple the drive shaft.

5. Locate the slip clutch bell shield, clamp, and mounting plate attached to the machine. Remove the

mounting bolts, flat washers, and lock washers from the gearbox face plate. Position the bell shield mounting

plate (flat side up) over the input shaft and align it with the threaded holes in the gearbox face plate. Secure

with bolts, flat washers, and lock washers previously removed.

Standard Assembly

Содержание 2000 Series





























































Результаты поиска

Содержание 2000 Series

Отзывы:

Похожие инструкции для 2000 Series

Бренды по названию

Популярные бренды

BROWN 2000 Series, Руководство владельца/оператора

Результаты поиска

Содержание 2000 Series

Отзывы:

Похожие инструкции для 2000 Series

Бренды по названию

Популярные бренды