BROWN 2000 Series Скачать руководство пользователя страница 14

Страница: 14 / 60

WARNINg

Transport with care.

Use slow-moving

vehicle emblem

and flashing light.

Follow local

traffic regulations.

Warning!

Transport with care.

Before transporting to a new location, make

certain that the slow-moving vehicle (SMV)

emblem is installed and is clearly visible.

Use flashing lights and follow local traffic

regulations.

Equipment Safety

CAUTION

keep machine

clean of debris.

Flammable debris

on machine poses

fire hazard.

Danger!

Protect bystanders, clear

work area of debris.

Do not operate the cutter near people. Debris

can be thrown hundreds of feet. Clear work

area of foreign objects such as wire, glass, and

other debris. Debris thrown by the cutter can

cause serious injury or death.

Warning!

Parking and dismount-

ing.

The rotating parts of this cutter continue to

rotate even after the PTO has been disengaged.

The operator should remain seated until rotation

has stopped. He should then set the brake, turn

off the engine, and remove the key. See tractor

manual for proper parking procedure.

Caution!

Avoid fires.

Keep the machine clean of debris, trash, and any

other flammable material.

WARNINg

Wait for all rotation

to stop before

dismounting

tractor.

Do not operate cutter

near bystanders. Clear

work area of debris

before operating.

DANGER

Содержание 2000 Series





























































Результаты поиска

Содержание 2000 Series

Отзывы:

Похожие инструкции для 2000 Series

Бренды по названию

Популярные бренды

BROWN 2000 Series, Руководство владельца/оператора

Результаты поиска

Содержание 2000 Series

Отзывы:

Похожие инструкции для 2000 Series

Бренды по названию

Популярные бренды