Brother NV1250D Скачать руководство пользователя страница 112

Страница: 112 / 212

110

UTILITY STITCHES

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

■

Using the optional quilting guide

Use the quilting guide to sew parallel stitches that
are equally spaced.

Insert the stem of the quilting guide into the
hole at the rear of the walking foot or presser
foot holder.

Walking foot

Presser foot holder

Adjust the stem of the quilting guide so that
the guide aligns with the seam that has already
been sewn.

Note

The optional quilting guide is available
through brother dealer.

Free-motion quilting

With free-motion quilting, lower the feed dogs (using
the drop feed lever) so that the fabric can be moved
freely in any direction.
When free-motion quilting, use the following
instructions with the optional quilting foot.

Note

Thread the needle manually when using the
quilting foot, or only attach the quilting foot
after threading the needle using the needle
threader.

Remove the presser foot and the presser foot
holder.

• Refer to “Removing and attaching the presser

foot holder” (page 46).

Secure the quilting foot with the presser foot
holder screw.

The pin on the quilting foot should be
positioned over the needle clamp screw.

Pin on quilting foot

Presser foot holder screw

Needle clamp screw

Hold the quilting foot in place with your right
hand, and then tighten the presser foot holder
screw using the screwdriver in your left hand.

Presser foot holder screw

Содержание NV1250D





















































































































































































































Результаты поиска

Содержание NV1250D

Отзывы:

Похожие инструкции для NV1250D

Бренды по названию

Популярные бренды

Brother NV1250D, Руководство по эксплуатации

Результаты поиска

Содержание NV1250D

Отзывы:

Похожие инструкции для NV1250D

Бренды по названию

Популярные бренды