Brother NV1250D Скачать руководство пользователя страница 201 | Manualshive

Страница: 201 / 212

background image

Troubleshooting

199

5

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

The sewing lamp

does not come on.

The sewing lamp is damaged.

Contact your retailer or the nearest
authorized service center.

–

The machine is not turned on.

Turn on the machine.

page 19

Nothing appears

in the LCD.

The brightness of the LCD is either
too light or too dark.

Adjust the brightness of the LCD.

page 204

Machine does not

operate when

button is pressed

.

An animation is displayed on the
LCD.

Touch the LCD with your finger, and
the animation will disappear.

page 20

Embroidery unit

does not move

.

No pattern selected.

Select a pattern.

page 159

The embroidery unit is not set up
correctly.

Set the embroidery unit up correctly.

page 150

Embroidery not

neatly done

.

The fabric is not fully stretched on
the embroidery frame. The fabric
is loose.

Stretch the fabric properly on the
embroidery frame.

page 154

No stabilizer material is attached.

Always use stabilizer material for
embroidery with stretch fabrics, thin
fabrics, fabrics with a loose weave
and fabrics where stitches easily
contract.

page 153

The thread is tangled and the
bobbin case, etc., is plugged up.

Remove the tangled thread. When
the bobbin case is plugged up, clean
the race.

page 184

The thread tension is incorrect.

Adjust the tension of the upper
thread.

page 173

Objects are placed near the
carriage or embroidery frame.

If the embroidery unit carriage or
embroidery frame bumps into
objects, the pattern will be
misaligned. Do not place objects
within the range of embroidery frame
motion.

page 151

Material coming out of the
embroidery frame is causing
problems.

Stretch the fabric on the frame once
again so that the material coming out
of the embroidery frame does not
cause problems, rotate the pattern
and embroider.

–

A heavy fabric is being
embroidered, and the fabric is
hanging off the table.

If embroidery is done with the fabric
hanging off the table, the embroidery
unit movement will be impaired.
Support the fabric while
embroidering.

–

The fabric is catching. It is
pinched.

Stop the sewing machine and set the
fabric up correctly.

–

The carriage was moved while the
embroidery frame was being
removed or attached during
embroidery.

If the carriage is moved during the
process, the pattern may be
misaligned. Be careful when
removing or attaching the
embroidery frame.

–

Symptom

Probable Cause

Remedy

Reference

«
...
199
200
201
202
203
...
»

Содержание NV1250D





















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NV1250D

Бренд: Janome Страницы: 68

Бренд: MAGIC FX Страницы: 20

Бренд: Sagem Страницы: 104

Бренд: Duerkopp Adler Страницы: 38

Union Special 36200L220-60

Бренд: JUKI Страницы: 56

Бренд: Necchi Страницы: 53

Adgressor BR 1050CS

Бренд: Nilfisk-Advance Страницы: 82

AMS-221EN/IP-420

Бренд: JUKI Страницы: 121

Бренд: JUKI Страницы: 4

Бренд: JUKI Страницы: 7

Бренд: JUKI Страницы: 18

Бренд: JUKI Страницы: 40

Бренд: JUKI Страницы: 4

Бренд: Brother Страницы: 16

Бренд: Brother Страницы: 60

Бренд: Brother Страницы: 19

Entrepreneur Pro PR1050X

Бренд: Brother Страницы: 12

Entrepreneur W PR680W

Бренд: Brother Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды