Brother NC-series Скачать руководство пользователя | Manualshive

Страница: 109 / 143

background image

USER’S GUIDE

12-2

- If you are using an older printer that does not support the 1284 bi-

directional parallel port standard, try executing the

SET PORT P1

ACKH ENABLED

and

SET PORT P1 DMA DISABLED

commands.

Also, make sure that fast strobe (FSTB) is disabled (do a

SHOW PORT

command to determine its state; if necessary, do a

SET PORT P1

FSTB DISABLED

command).

3. If the self-test page prints but you cannot print documents, try the

following

✒

Note

If none of the following steps are successful, there is almost certainly a
hardware or network problem!

a. If you have a VMS system or ULTRIX system, try making a connection

to the print server using the NCP (for VMS) or ccr (for ULTRIX)
utilities (see Appendix A if you don't know how to do this). If the
connection is successful, the hardware and network connections are OK,
so proceed to the LAT Troubleshooting Section. Otherwise, proceed to
step 4.

b. If you are using TCP/IP, try pinging the print server from the host

operating system prompt with the command ping ipaddress, where
ipaddress is the print server IP address (note that in some instances it can
take up to two minutes for the print server load its IP address). If a
successful response is received, then proceed to the UNIX
Troubleshooting section or Windows NT/LAN Server Troubleshooting
section. Otherwise, proceed to step 4.

c. If you have a Novell system, verify that the print server can be seen on

the network. To do this, login as the SUPERVISOR (not as someone
with supervisor privileges), go into PCONSOLE, select PRINT
SERVER INFORMATION, and select the name of the print server
(make sure that you have entered the print server name). If you can see

Print Server Status

and

Control

in the menu, then the

Brother print server visible to the network, proceed to the Novel
NetWare Installation Troubleshooting Section. Otherwise, go to step 4.

d. If you are running AppleTalk or PATHWORKS for Macintosh, make

sure that you can see the print server name under the LaserWriter 8 icon
in the Chooser. If it is visible, then the connection is good, so proceed to
the AppleTalk and PATHWORKS for Macintosh Section.

«
...
107
108
109
110
111
...
»

Содержание NC-series
















































































































































Отзывы:

Нет отзывов

Похожие инструкции для NC-series

Бренд: IBM Страницы: 54

Univerge SV9100

Бренд: NEC Страницы: 78

UNIVERGE SL2100

Бренд: NEC Страницы: 34

Бренд: NEC Страницы: 2

Бренд: NEC Страницы: 975

Бренд: Unitech Страницы: 2

Бренд: Datecs Страницы: 73

Бренд: Datamax Страницы: 12

E-Class Mark II

Бренд: Datamax Страницы: 40

Бренд: Datamax Страницы: 46

Бренд: Patton electronics Страницы: 331

Бренд: Oce Страницы: 12

Бренд: Oki Страницы: 24

Бренд: Cobalt Digital Inc Страницы: 218

Бренд: ONELAN Страницы: 24

Бренд: Patton electronics Страницы: 16

UniServer T1100 G3

Бренд: H3C Страницы: 138

AMX Vision2 V2-MASTER-1210

Бренд: Harman Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды