Brother HL-600 Series Скачать руководство пользователя страница 17

Страница: 17 / 84

CHAPTER 2 PAPER HANDLING

2–1

CHAPTER 2
PAPER HANDLING

PAPER SPECIFICATIONS

The printer can handle paper that has the following specifications.

Paper Type

Paper Size

Paper Weight

Sheet

Feeder

Manual

Cut sheet

A4, Letter, Legal, B5, A5,
Executive, Custom size
70-216 x 127-356 mm,
2.75-8.5 x 5-14 inches

60-135 g/m

(16-36 lbs)

●

Envelopes

DL, C5, COM-10,
Monarch

●

Organizer

Day-Timer

, J,K,L,M

70-216 x 127-356mm
2.75-8.5 x 5-11 inches

●

Labels

70-216 x 127-356 mm,

●

Trans-
parencies

2.75-8.5 x 5-14 inches

●

Paper Capacity in Feeder

Multi-purpose
Sheet Feeder :

Up to 22 mm (0.87 inch) in Height ( below the mark. )
Approx. 200 sheets of 75 g/m

(20 lbs) A4/Letter paper or 10

envelopes

Output Tray :

Approx. 100 sheets of 75 g/m

(20 lbs) A4/Letter paper

Remarks

It is recommended that you test paper, especially special sizes and types of
paper, on this printer before purchasing large quantities.

Avoid feeding labels with carrier sheets exposed, or your printer will be
damaged.

Use a recommended type of paper, especially plain paper and
transparencies, for optimum printing. For more information on paper
specifications, consult your nearest authorised sales representative or the
place of purchase of your printer.

We recommend you use label or transparancies which are designed for
laser printer.

We recommend you use long-grained paper for the best print quality.

If the paper will not load from the multi-purpose sheet feeder, use the
manual feed slot and try again.

Содержание HL-600 Series





















































































Результаты поиска

Содержание HL-600 Series

Отзывы:

Похожие инструкции для HL-600 Series

Бренды по названию

Популярные бренды

Brother HL-600 Series, Руководство пользователя

Результаты поиска

Содержание HL-600 Series

Отзывы:

Похожие инструкции для HL-600 Series

Бренды по названию

Популярные бренды