Brother HL-600 Series Скачать руководство пользователя страница 50

Страница: 50 / 84

USER’S GUIDE

5–10

CLEANING THE PRINTER

Clean the printer exterior and interior periodically. If printed pages get
stained with toner, clean the printer interior and drum unit.

✔

Warning

Before cleaning the printer, unplug the power cord.

Cleaning the Printer Exterior

Clean the printer exterior as follows:

1. Unplug the power cord.

2. Remove the paper in the multi-purpose sheet feeder.

3. Use a damp cloth for cleaning.

✒

Note

Use water or neutral detergents for cleaning. Cleaning with volatile
liquids such as thinners or benzene will damage the surface of the printer.

4. Wipe dirt and dust away from the printer exterior and feeder with a

cloth.

5. Load paper into the multi-purpose sheet feeder, and plug in the power

cord.

Содержание HL-600 Series





















































































Результаты поиска

Содержание HL-600 Series

Отзывы:

Похожие инструкции для HL-600 Series

Бренды по названию

Популярные бренды

Brother HL-600 Series, Руководство пользователя

Результаты поиска

Содержание HL-600 Series

Отзывы:

Похожие инструкции для HL-600 Series

Бренды по названию

Популярные бренды