Brother HL-600 Series Скачать руководство пользователя страница 36

Страница: 36 / 84

USER’S GUIDE

4–2

Selecting the RS-422A (Apple) or RS-232C (IBM) Serial Interface

✒

Note

This section is only for printer models which have had the serial interface
installed.

☛

Caution

Be sure to select the serial interface type to match your computer as
follows:

•

Select RS-422A(Apple) for Macintosh computers: because RS-422A
has been factory selected, if you are using a Macintosh computer, you
do not need to change the setting. You may skip this section.

•

Select RS-232C(IBM) or RS-422A(Apple) for PCs that operate with
DOS or Windows.

If necessary, select the interface type as follow:

1. Make sure that the printer is in the off-line state.

2. Select the RS-422A(Apple) or RS-232C(IBM) interface by changing

the serial interface slide switch to the right for IBM(RS-232C) or to
the left side for Apple(RS-422A).

Fig. 4-2 Selecting the RS-422A (Apple)

or RS-232C (IBM) Serial Interface

Содержание HL-600 Series





















































































Результаты поиска

Содержание HL-600 Series

Отзывы:

Похожие инструкции для HL-600 Series

Бренды по названию

Популярные бренды

Brother HL-600 Series, Руководство пользователя

Результаты поиска

Содержание HL-600 Series

Отзывы:

Похожие инструкции для HL-600 Series

Бренды по названию

Популярные бренды