Brother HL-4200CN Скачать руководство пользователя страница 267

Страница: 267 / 366

V-61

TRANSFER ROLL CARTRIDGE ADJUSTING THIRD TRANSFER
CURRENT VALUE

The transfer current value of the toner image is set so that the image quality can get for

each type of paper. This set value is selected by assuming the average characteristic

per paper type, therefore, the best image quality may not appear if the paper to be used

has the different characteristic from the one which Brother assumes.

In this case, the image quality can be improved by changing the transfer current value to

the one which corresponding to the paper used actually.

<Image troubles which may be caused when the transfer current value is not

appropriate>

1) In case that the transfer current is "not enough":

Toner splash at the edge of image and unbalanced color (Whole image has bluish

tinge) are caused.

-> Increase the transfer current

2) In case that the transfer current is "excess":

1mm flakes appear on the entire image.

-> Reduce the transfer current

Note:

There is high possibility to cause these image errors to the second side especially
when executing duplex printing.

6.1

Procedure of Changing the Transfer Current Value Setup

The transfer current value setup is changed on the control panel.

Ready Alarm

Menu

Form Feed

Set

Job

Cancel

Back

Fig.5-10

1. With the status of Ready to Print (Printer screen (printable)), press [Menu] button.

2. After Menu screen (1:System) is displayed, press

button.

3. After Menu screen (2:Maintenace) is displayed, press [Form Feed/Set] button.

5.Menu

3.Form Feed/Set button

2.Up/Down button

Ready to Print

1:System

2:Maintenance

Содержание HL-4200CN















































































































































































































































































































































































Результаты поиска

Содержание HL-4200CN

Отзывы:

Похожие инструкции для HL-4200CN

Бренды по названию

Популярные бренды

Brother HL-4200CN, Руководство по обслуживанию

Результаты поиска

Содержание HL-4200CN

Отзывы:

Похожие инструкции для HL-4200CN

Бренды по названию

Популярные бренды