16
button (28) is pressed. Each LED here corresponds to
about 20 % of capacity. When the battery pack (26) is
fully charged, all five LEDs light up. The charge level of
the switched-on battery pack (26) is also shown on the
display in the display unit (1) (see „Battery charge and
remaining range“ on page 11). If the capacity of the
battery pack (26) is below 10 %, the first LED of the
charge level display (27) flashes.
The battery pack (26) can be charged with and without
the display unit (1). Without the display unit (1), the
charging operation can only be tracked at the charge
level display (27) of the battery pack (26). The display
unit (1) can be removed during charging or fitted only
after the charging operation has started. The charge
level is indicated by the charge level display (27) on the
battery pack (26) and by the bar (13) on the display unit.
During charging, the LEDs of the charge level dis-
play (27) on the battery pack (26) light up. Each steady
LED corresponds to about 20 % of capacity. The flas-
hing LED shows the charging of the next 20 %.
During charging, the charge level display (27) is as fol-
lows:
LED steady
LED flashing
Charge level
-
1
0-19 %
1
2
20-39 %
1, 2
3
40-59 %
1, 2, 3
4
60-79 %
1, 2, 3, 4
5
80-99 %
1, 2, 3, 4, 5
-
End of charging, battery
pack 100 % charged
Operation
Switching battery pack on and off
Switching on the battery pack (26) is one of the options
for switching on the Brose e-Bike System.
−
Press the LED button (28) on the battery pack (26).
→
The LEDs of the charge level display (27) come on
briefly and then show the current charge level for
about 4 seconds.
N.B.: If the capacity of the battery pack (26) is below
10 %, only the first LED of the charge level display (27)
flashes.
−
To switch off the battery pack (26), press the LED
button (28) for > 3 seconds.
→
The LEDs of the charge level display (27) go out.
→
The e-Bike System too is also switched off.
Operating modes of battery pack
Active Mode
After switch-on, the battery pack (26) is in the “Active
Mode”. It remains in the “Active Mode” for 2 hours wit-
hout any further action (operation or movement of the
e-Bike).
The “Active Mode” is activated by operating the LED
button (28), by charging the battery pack (26), or by in-
serting the battery pack (26) into the e-Bike.
Deep Sleep Mode
To minimize the power consumed by the system itself,
the battery pack (26) switches automatically to the
“Deep Sleep Mode” after 2 hours in the “Active Mode”
without any activity and with the display unit (1) swit-
ched off. The “Deep Sleep Mode” is also activated
when the LED button (28) or the On/Off button (8) of the
display unit (1) is pressed for > 3 seconds or when the
battery pack (26) is not inserted into the e-Bike for lon-
ger than 30 seconds.
Power reduction of battery pack
For self-protection against overloading or overheating,
the battery pack (26) has a function for automatic power
reduction depending on the charge level and tempera-
ture.
Above a cell temperature of 70°C, and between 0 and
10°C, the motor power is reduced in 4 stages (25 %
each) until the drive is switched off.
With a charge level of < 5 %, the drive assist is switched
off, so that the display unit (1) and the lights can be
operated for at least 4 more hours before the battery
pack (26) deactivates for self-protection.
Maintenance, cleaning and storage
Keep the battery pack (26) clean. Clean it carefully with
a soft and dry cloth. The battery pack (26) must not be
immersed in water or cleaned using a water jet. If the
battery pack (26) is no longer working, please contact
an authorized bicycle dealer. Set down the battery
pack (26) only on clean surfaces. Avoid in particular any
fouling of the charging sockets (30) and of the contacts.
The service life of the battery pack (26) can be extended
if it is looked after well and above all stored in the right
conditions:
Temperature
18-23°C
Humidity
0-80 %
Charge level
70 %
