Brookfield DV-III ULTRA Скачать руководство пользователя страница 15

Страница: 15 / 133

Brookfield Engineering Laboratories, Inc.

Page 15

Manual No. M/98-211-B0104

Brookfield Engineering Laboratories, Inc.

Page 15

Manual No. M98-211-E0912

I.11 Connections

The DV-III Ultra Rheometer is capable of communicating with several external devices to enhance

operation. The cables and connections required for proper communication are detailed below.

RHEOLOADER

The

DVP-202 USB Cable is used to connect the USB Port on the DV-III Ultra Base to the computer.

The

DVP-80 cable is used to connect the RS-232 serial port on the DV-III Ultra base to Com Port

1 or Com Port 2 on the computer. Some PCs may also have Com Port 3 and Com Port 4. These

cables are supplied with the DV-III Ultra.

RHEOLOADER AND EZ-YIELD SOFTWARE

The

DVP-80 cable is used to connect the RS-232 serial port on the DV-III Ultra base to Com Port

1 or Com Port 2 on the computer. Some PCs may also have Com Port 3 and Com Port 4. This

cable is supplied with the DV-III Ultra.

RHEOCALC SOFTWARE

The

DVP-202 USB Cable is used to connect the USB Port on the DV-III Ultra Base to the computer.

The

DVP-80 cable is used to connect the RS-232 serial port on the DV-III Ultra base to Com Port

1 or Com Port 2 on the computer. Both cables are supplied with the RHEOCALC software.

ARALLEL PRINTER

The

CAP-86 cable is used to connect the 25-pin parallel port on the DV-III Ultra base with the

Centronics port on the printer.

SERIAL PRINTER

The

DVP-81 cable is used to connect the 9-pin serial port on the DV-III Ultra with the 25-pin serial

port on a printer.

THERMOSEL CONTROLLER AND TC SERIES TEMPERATURE BATHS

Earlier model baths with programmable Brookfield Controllers will also work.

The

DVP-141 cable is used to connect the serial port on the DV-III Ultra base to the serial port on

the controller. This cable is supplied with the controller/bath.

Be sure that the controller temperature probe is properly located in the control device (Thermosel

or bath) and connected to the controller.

Note:

1. The controller may alternately communicate with Rheocalc V.2.0 or

higher software. In this configuration, the controller is connected to the

computer through either Com Port 1 or Com Port 2 by using the DVP-80

cable. The DV-III Ultra can also be connected to a computer through

the USB Port by using the DVP-202 cable.

2. The controller must also be connected to the control device (Thermosel

or bath) with the appropriate load cable.

Содержание DV-III ULTRA






































































































































Результаты поиска

Содержание DV-III ULTRA

Отзывы:

Похожие инструкции для DV-III ULTRA

Бренды по названию

Популярные бренды

Brookfield DV-III ULTRA, Руководство по эксплуатации

Результаты поиска

Содержание DV-III ULTRA

Отзывы:

Похожие инструкции для DV-III ULTRA

Бренды по названию

Популярные бренды