Brookfield DV-III ULTRA Скачать руководство пользователя страница 71

Страница: 71 / 133

Brookfield Engineering Laboratories, Inc.

Page 71

Manual No. M98-211-E0912

Download

Selecting Download (using the

Download

button or the

Download Program

option in the

Utility menu) sends the parameters displayed on the Test Parameters page to the specified memory

location in the DV-III Ultra Rheometer. After a few seconds, a dialog box appears indicating that

the rheometer received the parameters.

If no dialog box appears, see

Appendix J - Troubleshooting

- to help determine why the parameters

were not received by the rheometer.

Run

Selecting

Run

and a program number (using the

Run

button or the

Run Program

option in the

Utility

menu) directs the DV-III Ultra Rheometer to run the selected program.

Note:

The program numbers refer to the memory locations in the DV-III Ultra

Rheometer.

After a few seconds, the DV-III Ultra tells EZ-Yield that the test has begun. Once all optional

preparation steps have been performed by the rheometer, EZ-Yield begins to receive data as the

test runs. If the On-Line Plotting option is selected in EZ-Yield, the Graph page is automatically

displayed as soon as the first data point is received. Data are plotted as received, while being

displayed in the Data/Results section of the Data page.

If the rheometer is running the test and no data appears, see

Appendix J- Troubleshooting

- to

help determine why EZ-Yield is not receiving the data. When the test is complete, a dialog box is

displayed asking you to save the freshly collected data and results.

Help

Selecting Help (using the Help button or the Help option on the menu) displays the on-line help

system.

Exit

Selecting Exit (using the Exit button or the Exit option on the File menu) exits the EZ-Yield software.

If test parameters or data have not yet been saved, a dialog box appears informing you of this fact

and giving you the opportunity to save the pertinent information.

COM Port

Select the COM Port on the host PC (sometimes referred to as a serial port or an RS-232 port) to

which the DV-III Ultra Rheometer is attached. COM1 through COM4 may be selected. Selecting

NONE disconnects the rheometer from the host PC.

Note:

Simply selecting the COM port is only part of what is needed for a

valid connection between the rheometer and the host PC. Ensure that

the appropriate cable is in use (Brookfield part # DVP-80) and that it

is connected properly. See Appendix I - DV-III Ultra to COmputer

Command Set - for more information regarding the DV-III Ultra to host

PC connection.

Содержание DV-III ULTRA






































































































































Результаты поиска

Содержание DV-III ULTRA

Отзывы:

Похожие инструкции для DV-III ULTRA

Бренды по названию

Популярные бренды

Brookfield DV-III ULTRA, Руководство по эксплуатации

Результаты поиска

Содержание DV-III ULTRA

Отзывы:

Похожие инструкции для DV-III ULTRA

Бренды по названию

Популярные бренды