Bromic Heating Tungsten Smart-Heat Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 26

background image

19

www.bromicheating.com

CONTINUED...

To set heater head angle at high position,

manually push heater head up to align hole then

insert slip pin.

To set heater head angle at low position, remove

slip pin & allow heater head to rest in low posi-

tion. Slip pin does not need to be inserted.

CAUTION: ONLY ADJUST THE HEATER HEAD ANGLE PRIOR TO OPERATION. ADJUSTING WHILST UNIT IS IN

OPERATION OR POST OPERATION CAN CAUSE SERIOUS BURNS

Adjusting the heater head angle

High Head Tilt Position

INSTALLATION INSTRUCTIONS

CONTINUED...

«
...
17
18
19
20
21
...
»

Содержание Tungsten Smart-Heat



























Отзывы:

Нет отзывов

Похожие инструкции для Tungsten Smart-Heat

Бренд: Warren Controls Страницы: 16

Бренд: UNITED Страницы: 8

Бренд: Bartlett Страницы: 5

Бренд: ICP DAS USA Страницы: 4

Бренд: ICP DAS USA Страницы: 6

EIP-2000 Series

Бренд: ICP DAS USA Страницы: 19

Бренд: WAREMA Страницы: 4

Бренд: L-Acoustics Страницы: 24

Бренд: L-Acoustics Страницы: 21

Бренд: M&S Systems Страницы: 4

Бренд: IBM Страницы: 20

Бренд: DAV TECH Страницы: 24

Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 16

Бренд: RADEMACHER Страницы: 68

sensoCOMFORT VRC 720/3

Бренд: Vaillant Страницы: 64

Бренд: Ban Seok Страницы: 9

Pulsafeeder MPC Vector

Бренд: Idex Страницы: 114

Бренд: Voltech Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды