Bromic Heating Tungsten Smart-Heat Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 26

background image

13

www.bromicheating.com

INSTALLATION INSTRUCTIONS

CONTINUED...

STEP 6:

Slide top arms over front assembly slip joints - Ensure top screw holes are faced inwards.

Secure the front panel to top arms using 4 x M5 screws and supplied M5 Hex Key.

STEP 7:

Secure the top arms to lower arm slip joint using 2 x M8 x45 screws and supplied M8 Hex Key.

* Note: The joint between the lower and upper arms is firm to

ensure` rigidily and stability of the product. To engage slowly lever

the two sections together using some force and push down fully

L

R

«
...
11
12
13
14
15
...
»

Содержание Tungsten Smart-Heat



























Отзывы:

Нет отзывов

Похожие инструкции для Tungsten Smart-Heat

Бренд: K&K Страницы: 6

Бренд: Wavetec Страницы: 17

Бренд: Calsense Страницы: 9

Smart Controller

Бренд: MaestroHome Страницы: 10

Бренд: QCON Страницы: 4

Бренд: H3C Страницы: 5

Бренд: H3C Страницы: 4

Бренд: Hama Страницы: 7

Бренд: Hama Страницы: 44

Бренд: RadioMaster Страницы: 10

Бренд: K&K Страницы: 6

Бренд: Rain Bird Страницы: 24

ESP-LXIVM Series

Бренд: Rain Bird Страницы: 16

Бренд: Rabe Страницы: 61

Бренд: Racal Instruments Страницы: 35

Бренд: GBD Страницы: 60

MagicSpeed Series

Бренд: Waeco Страницы: 76

Бренд: Brand Innovations Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды