Bromic Heating Tungsten Smart-Heat Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 26

background image

5

www.bromicheating.com

PRODUCT OVERVIEW

PRODUCT DESCRIPTION

The TUNGSTEN Gas Radiant Heater is designed to provide effective outdoor heating to both commercial and residential
premises whilst offering an appealing design.

The heater incorporates a pivoting head and adjustable heat output for precise heat control. The heater has been designed
to withstand the rigors of the outdoors.

SPECIFICATIONS

TUNGSTEN SMART-HEAT™ HEATER DIMENSIONAL DETAILS

IMPORTANT

This appliance is to be protected from rain. Install under a protective cover.
This appliance shall only be used in an above ground, open-air situation with sufficient natural ventilation. The heater
must not be operated in any stagnant areas and should be positioned where any potential gas leakage and products of
combustion are rapidly dispersed by wind and natural convection.

!

TUNGSTEN Smart-Heat™

Ignition

1.5V repetitive spark ignitor

Manufactured by

BROMIC PTY. LTD

ETL approval number

4009079

Gas consumption

21,304 BTU - 38,500 BTU

Gas Type

Propane Gas (LPG) only

Gas Supply

20Lb (9kg) LP- Gas Cylinder

Injector size

0.85mm

Weight

56Kg - 123.5lB

Safety features

Flame failure device, anti-tilt switch

Gas supply pressure

Min 11”wc – Max 14”wc

2160mm

7.1ft

700mm

2.3ft

700mm

2.3ft

«
...
3
4
5
6
7
...
»

Содержание Tungsten Smart-Heat



























Отзывы:

Нет отзывов

Похожие инструкции для Tungsten Smart-Heat

Бренд: Nelsen Corporation Страницы: 16

Бренд: National Instruments Страницы: 34

7000-2 - Escalade RAID Controller

Бренд: 3Ware Страницы: 2

Бренд: GARAN Страницы: 8

Бренд: Gamma Vacuum Страницы: 25

Бренд: Gamma Страницы: 28

Бренд: Scanreco Страницы: 10

Бренд: Teledyne Страницы: 102

Бренд: Tamiya Страницы: 5

OPTISWITCH 5100 C

Бренд: KROHNE Страницы: 40

Бренд: U-Tron Страницы: 8

Бренд: Agilent Technologies Страницы: 20

Бренд: YASKAWA Страницы: 42

Бренд: YASKAWA Страницы: 351

Бренд: Gardena Страницы: 15

Бренд: Zander Aachen Страницы: 75

Бренд: CP Electronics Страницы: 12

Бренд: National Instruments Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды