background image

5-4

COVER AND YOKE REMOVAL

To remove complete cover and yoke 
assembly:

1. Keep the cover in its CLOSED posi-

tion.

2. Remove two thumbscrews (25) attach-

ing the lift assembly cover and remove 
from assembly (20).

3. Raise the cover to its full open position 

and place a solid support under the lift 
to keep it in raised position.

4. Place a plastic, metal or wooden 

board across well opening to support 
cover and yoke assembly.

5. Remove gas spring keepers from both 

ends of the three gas springs.

Cover Assembly is very 
heavy. DO NOT allow 

cover assembly to fall. Serious injury or 
damage to the unit may result.

6.  Push up on cover until the two outer 

gas springs are at their full extension. 
While holding the cover up, pop them 
off the ballstuds at the large end of 
both springs. Then raise the cover fur-
ther until the center gas spring is at its 
full extension and pop it off also.

7. Lower cover to the support block 

holding it in the up position.

When performing the next 
step be extremely careful 

so that the support does not become 
dislodged. Cover is very heavy. If it falls, 
serious injury or damage to unit may 
result.

8.  Pop the other end of the gas springs 

off of the ballstuds on the mounting 
blocks.

9. Carefully lower cover assembly to the 

support board over the well.

Cover Assembly is very 
heavy. DO NOT allow 

cover assembly to fall. Serious injury or 
damage to the unit may result.

broaster.com   Manual #15460 8/02   Rev 6/15

Содержание 2004E





























































































Отзывы: