© BriskHeat
®
Corporation. All rights reserved.
3
XtremeFLEX
®
BSAT
Silicone Rubber Heating Tape
Never handle the heater while it is in
operation; always disconnect the heater
from the power source and allow to cool
prior to handling.
Inspect product before use (see page 6).
Do not use heater with torn or worn
surfaces or other visual damage.
Do not wrap the heater over itself
Do not repair damaged or faulty heaters.
Do not crush or apply severe physical
stress on heater or cord assembly.
Unplug heater when not in use.
Fasten heater to device using approved
methods only.
If spillage of foreign matter onto heater
occurs, disconnect from power source and
clean after heater has been allowed to
cool.
Never operate a heater without an
appropriate heat sink (device being heated
is considered a heat sink).
Make sure there is a uniform fit prior to
energizing. If there are air gaps between
surface to be heated and the heater, hot
spots can occur and could result in
damage due to overheating.
IMPORTANT SAFETY INSTRUCTIONS
Do not immerse heater in liquid.
Keep volatile or combustible material away
from heater when in use.
Do not use heater in hazardous locations
Keep sharp metal objects away from
heater.
Only qualified personnel are allowed to
connect electrical wiring.
Disconnect all supply power at the source
before making any power connections.
All electrical wiring must follow local
electrical codes.
The end-user is responsible for providing a
suitable electrical disconnect.
The end-user is responsible for providing a
suitable electrical protection device. It is
highly recommended that a GFCI be used.
A person who has not read and understood all
operating instructions is not qualified to operate
this product.
Immediate hazards which
WILL
result in severe
personal injury or death
Hazards or unsafe practices that
COULD
result in
severe personal injury or death
Hazards or unsafe practices that
COULD
result in
minor personal injury or property damage
SAFETY ALERT SYMBOL
The symbol above is used to call your attention to
instructions concerning your personal safety. It
points out important safety precautions. It means
“
ATTENTION! Become Alert! Your Personal
Safety is involved!
” Read the message that
follows and be alert to the possibility of personal
injury or death.
© BriskHeat
®
Corporation. All rights reserved.
4
XtremeFLEX
®
BSAT
Silicone Rubber Heating Tape
SPECIFICATIONS
Operating Conditions:
Maximum Exposure Temperature: 450°F (232°C)
Maximum Humidity: 95% RH
Heater Characteristics:
Width
in (mm)
Length
in (mm)
Total
Watts
Part Number
120VAC
Part Number
240VAC (No plug)
0.5 (13)
24.0 (610)
72
BSAT051002
BSAT052002
0.5 (13)
48.0 (1220)
144
BSAT051004
BSAT052004
0.5 (13)
72.0 (1830)
216
BSAT051006
BSAT052006
0.5 (13)
96.0 (2440)
288
BSAT051008
BSAT052008
0.5 (13)
120.0 (3050)
360
BSAT051010
BSAT052010
1.0 (25)
24.0 (610)
144
BSAT101002
BSAT102002
1.0 (25)
48.0 (1220)
288
BSAT101004
BSAT102004
1.0 (25)
72.0 (1830)
432
BSAT101006
BSAT102006
1.0 (25)
96.0 (2440)
576
BSAT101008
BSAT102008
1.0 (25)
120.0 (3050)
720
BSAT101010
BSAT102010
2.0 (51)
24.0 (610)
288
BSAT201002
BSAT202002
2.0 (51)
48.0 (1220)
576
BSAT201004
BSAT202004
2.0 (51)
72.0 (1830)
864
BSAT201006
BSAT202006
2.0 (51)
96.0 (2440)
1152
BSAT201008
BSAT202008
2.0 (51)
120.0 (3050)
1440
BSAT201010
BSAT202010
3.0 (76)
24.0 (610)
432
BSAT301002
BSAT302002
3.0 (76)
48.0 (1220)
864
BSAT301004
BSAT302004
3.0 (76)
72.0 (1830)
1296
BSAT301006
BSAT302006
3.0 (76)
96.0 (2440)
1440
BSAT301008
BSAT302008
3.0 (76)
120.0 (3050)
1440/1800
BSAT301010
BSAT302010
Time Percentage Dial Controller
120V Model with NEMA 1-15 Plug
240V Model without plug
Power Density: 6.0 watts/in² (0.009 watts/mm²)
Moisture and Chemical Resistant
Suitable for use on Electrically Conductive Surfaces
