Briggs & Stratton Vanguard 1100000, Руководство оператора

Страница: 7 / 28

7
en
Engines give off carbon monoxide, an odorless, colorless, poison gas.
Breathing carbon monoxide can cause nausea, fainting or death.
WARNING
•
Start and run engine outdoors.
•
Do not start or run engine in enclosed area, even if doors or windows are open.
NOTICE: This engine was shipped from Briggs & Stratton without oil. Before you start
the engine, make sure you add oil according to the instructions in this manual. If you
start the engine without oil, it will be damaged beyond repair and will not be covered
under warranty.
Note: Equipment may have remote controls. See the equipment manual for location and
operation of remote controls.
1. Check the oil level. See the
How To Check/Add Oil section.
2. Make sure equipment drive controls, if equipped, are disengaged.
3. Turn the fuel shut-off valve (
A ), if equipped, to the on position (Figure 5).
4. Move the choke control lever ( B ) to the choke position.
Note: Choke is usually unnecessary when restarting a warm engine.
5. Move the throttle control lever ( C ), if equipped, to the fast position. Operate
the engine with the throttle control lever in the fast position.
6. On engines equipped with a stop switch ( D ), move the switch to the on position.
7.
Rewind Start:
Firmly hold the starter cord handle (
E
). Pull the starter cord handle
slowly until resistance is felt, then pull rapidly.
Note: If the engine does not start after repeated attempts, go to
BRIGGSandSTRATTON.COM or call 1-800-233-3723 (in USA).
WARNING:
Rapid retraction of the starter cord (kickback) will pull your
hand and arm toward the engine faster than you can let go. Broken bones, fractures,
bruises or sprains could result. When starting engine, pull the starter cord slowly until
resistance is felt and then pull rapidly to avoid kickback.
8. Electric Start: Turn the electric start switch ( F ) to the on/start position.
Note: If the engine does not start after repeated attempts, go to
BRIGGSandSTRATTON.COM or call 1-800-233-3723 (in USA).
9. As the engine warms up, move the choke control ( B ) to the run position.
How To Stop The Engine - Figure
5
WARNING
Gasoline and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
•
Do not choke the carburetor to stop engine.
1. Electric Start: With the throttle control ( C ) in the slow position, turn the
electric start switch ( F ) to the off position (Figure 5). Remove the key and keep in a
safe place out of the reach of children.
2. Rewind Start: Push the stop switch ( D ) to the off position,
or
Move the throttle control ( C ) to the stop position.
3. After the engine stops, turn the fuel shut-off valve ( A ), if equipped, to the closed
position.
Maintenance
Use only original equipment replacement parts. Other parts may not perform as
well, may damage the unit, and may result in injury. In addition, use of other parts
may void your warranty.
We recommend that you see any Briggs & Stratton Authorized Dealer for all
maintenance and service of the engine and engine parts.
NOTICE: All the components used to build this engine must remain in place for proper
operation.
Emissions Control
Maintenance, replacement, or repair of the emissions control devices and systems
may be performed by any non-road engine repair establishment or individual.
However, to obtain “no charge” emissions control service, the work must be performed
by a factory authorized dealer. See the Emissions Warranty.
Unintentional sparking can result in fire or electric shock.
Unintentional start-up can result in entanglement, traumatic
amputation, or laceration.
Fire hazard
WARNING
Before performing adjustments or repairs:
•
Disconnect the spark plug wire and keep it away from the spark plug.
•
Disconnect battery at negative terminal (only engines with electric start.)
•
Use only correct tools.
•
Do not tamper with governor spring, links or other parts to increase engine
speed.
•
Replacement parts must be the same and installed in the same position as the
original parts.
•
Do not strike the flywheel with a hammer or hard object because the flywheel
may later shatter during operation.
When testing for spark:
•
Use approved spark plug tester.
•
Do not check for spark with spark plug removed.
Maintenance Chart
First 5 Hours
•
Change oil
Every 8 Hours or Daily
•
Check engine oil level
•
Clean area around muffler and controls
•
Clean finger guard
Every 25 Hours or Annually
•
Clean air filter *
•
Clean pre-cleaner *
Every 50 Hours or Annually
•
Change engine oil
•
Check muffler and spark arrester
Annually
•
Replace air filter
•
Replace pre-cleaner
•
Replace spark plug
•
Clean fuel filter
•
Clean air cooling system *
•
Check valve clearance **
* In dusty conditions or when airborne debris is present, clean more often.
** Not required unless engine performance problems are noted.
Carburetor Adjustment
Never make adjustments to the carburetor. The carburetor was set at the factory to
operate efficiently under most conditions. However, if adjustments are required, see any
Briggs & Stratton Authorized Dealer for service.
NOTICE: The manufacturer of the equipment on which this engine is installed specifies
the top speed at which the engine will be operated. Do not exceed this speed.
How To Replace The Spark Plug - Figure
6
Check the gap ( A , Figure 6) with a wire gauge ( B ). If necessary, reset the gap. Install
and tighten the spark plug to the recommended torque. For gap setting or torque, see the
Specifications section.
Note: In some areas, local law requires using a resistor spark plug to suppress ignition
signals. If this engine was originally equipped with a resistor spark plug, use the same
type for replacement.
Not for Reproduction