![background image](http://html1.mh-extra.com/html/breville/the-dynamic-duo-bep920/the-dynamic-duo-bep920_instruction-booklet_2809021020.webp)
38
39
CARE & CLEANING
c)
Press UP or DOWN arrow to set mode, the
‘dESC’ will appear on the LCD. Press the
MENU button to enter Descale mode.
2 – Empty Boilers
a)
Remove the grey silicone cover on the
lower front panel marked DESCALE
ACCESS. Place a cloth over the drip tray
to stop steam escaping.
REMOVE
b)
Use a flat-head screwdriver to rotate the
right screw counter-clockwise until the
valve is fully open. As the valve opens,
steam may be released.
NOTE
If there’s no water released into the
drip tray, press and hold the 1 CUP
button for 3 seconds. This will release
water from the boiler
When the water is completely empty, close
the valve by rotating screws clock-wise until
seated. Do not overtighten screws to avoid
damages to the valves.
c)
Next, repeat the above process on the
left screw.
d)
Empty the drip tray. Use caution as the
drip tray may be hot.
e)
Empty water tank, remove water filter.
f)
Place descale solution into water tank,
fill with cold water to MAX line,
(if an alternative cleaning solution is
used, please follow the manufacturer’s
instructions accordingly). Lock water
tank back into position at the back of
the machine.
NOTE
If water tank has not been removed,
replaced or is empty, “FILL TANK”
will appear on the LCD.
3 – Begin Descale
Press MANUAL button to proceed.
Machine will fill boilers with descale solution
and heat to temperature. During this time,
water may flow through the group head.
Wait for countdown timer to reach 0. This
allows solution to dissolve scale build-up.
However you can proceed to the next step at
any time by pressing the 1 Cup button.
a)
Place a cloth over the drip tray to stop
steam escaping.
b)
Empty boilers by repeating steps
2b and 2d.
c)
Empty drip tray and insert back to place.
d)
Empty water tank then rinse and fill with
clean water to the MAX line. Lock water
tank back into position.
4 – Flush Boilers
Press MANUAL button to proceed.
During this procedure, the LCD will show
countdown time (20 minutes).
During this time, the machine will fill boilers
with fresh clean water and heat to temperature.
You can proceed to the next step at any time by
pressing the 1 Cup button.
a)
Place a cloth over the drip tray to stop
steam escaping.
b)
Empty boilers by repeating steps
2b and 2d.
c)
Empty drip tray and insert back to place.
d)
Empty water tank then rinse and fill with
clean water to the MAX line. Lock water
tank back into position.
5 - Repeat Step 4 Flush Boilers
We recommend flushing boilers again to
ensure any residual descale solution is
released from the boilers.
Press POWER button to escape the Descale
mode. The descale process is now complete
and ready to use.
THE SMART GRINDER™ PRO CARE,
CLEANING & STORAGE
1.
Empty beans from the hopper and
grind out any excess beans
(see below).
2.
Unplug power cord from power
outlet before cleaning.
3.
Wash the grind container and lid,
bean hopper and lid in warm soapy
water, rinse and dry thoroughly.
4.
Wipe and polish exterior of
appliance with a soft damp cloth.
NOTE
Do do not use alkaline or abrasive
cleaning agents, steel wool or
scouring pads, as these can damage
the surface.
NOTE
We recommend you do not clean any
grinder parts or accessories in the
dishwasher.
CARE & CLEANING
Содержание The Dynamic Duo BEP920
Страница 25: ...48 49 PAGE HEADER NOTES NOTES...