manualshive.com logo in svg

Breezair TBQ, Руководство по установке, Страница: 6 / 20

Поделиться
Скачать
Breezair TBQ Скачать руководство пользователя страница 6

6 

 |   

COOLER LOCATION 

Check proposed cooler location to ensure it is structurally 

capable of supporting the weight of the cooler. If the roof is 

structurally inadequate, provide an alternate load bearing 

structure.
The ideal location for the cooler is in a central position on the 

roof (away from sleeping areas and where people spend most 

of their time) so that the duct runs are of approximately the 

same length. Carefully consider neighbouring residences and 

noise levels when locating the cooler, if necessary talk to the 

customer and the neighbour before carrying out the installation.
Always locate the cooler where it will receive adequate fresh air 

and not in a recess where it may be starved for air or where the 

air is polluted. Ensure that the cooler is installed such that the 

fan is facing an unoccupied space.
Ensure location is a minimum of: 
• 

3m/10’ from a solid fuel heater flue, 

• 

1.5m/5’ from a gas flue, 

• 

5m/17’ from a sewer vent, and 

• 

600mm/2’ from a wall.

The cooler must be mounted at least 3m/10’ (preferably  

5m/17’) away from any TV antenna or antenna cables.

Make sure the cooler is not between the antenna and the 

transmission tower that is providing the television signal  

to the home.
Allow adequate access to and around the cooler for 

maintenance. Provision must be made for access to electricity, 

water supplies and drains.

Note!

 Do you need to discuss the installation of items like 

safety anchor points with the customer?

ILL1150-A

ILL1155-C

ILL1155-C

Lift the venturi and fan assembly out of the cooler. Take care 

with the motor lead, which will be sitting loosely in the bottom  

of the cooler.
The venturi and fan assembly can be placed on to the ground 

until the rest of the cooler has been installed on the dropper.

REMOVING THE TRANSITION

Turn the cooler onto its side to remove the transition.  

There are clips in each of the four corners that will disengage 

once the transition is given a firm pull.
If any of the corners are difficult to remove do not use 

 

excessive force. Gently squeeze the clips together and  

remove the transition one corner at a time.

REMOVING THE VENTURI 

Once the pad frames have been removed, detach the venturi 

and fan assembly.
Disengage the two venturi clips as shown.

Note!

 Ensure the steel restraint cable and motor cable are 

secured against the side of the venturi by the sticker provided.

X

x

ILL1150-A

ILL1093-E

Sticker securing cables

Содержание TBQ





















Отзывы:

Нет отзывов