manualshive.com logo in svg

Breezair TBQ, Руководство по установке, Страница: 15 / 20

Поделиться
Скачать
Breezair TBQ Скачать руководство пользователя страница 15

TBQ/TBS EVAPORATIVE COOLER INSTALLATION MANUAL  

|  

15

 

ILL1714-A

ILL1615-A

SETTING THE WATER LEVEL 

cont

Turn on the mains water supply to the cooler. 
Turn the cooler on at the Controller, in “COOL” mode.
Adjust set temperature slider to be close to current room 

temperature so that fan speed remains low.

Allow the tank (reservoir) to fill with water. The float valve will 

eventually stop the water from entering the cooler. Wait for this 

to happen and check the water level.

ILL998-D

If the level is too high rotate the float clockwise. Drain some 

water from the tank and allow it to refill to the new set point. 

 

If too low rotate the float in an anti-clockwise direction. The 

correct water level is approximately 5mm / 3/16” below the 

surface of the tank the float valve is mounted on. It is advisable 

to check the water level again after the float valve washer has 

“bedded in”.

Cooler operating information is available from the ‘Service 

Operating Screen’ under the COOLER tab of the SETTINGS 

menu.

SETTING THE WATER LEVEL

Isolate power to the cooler electronics and disconnect the 

pump, making sure the plug is kept away from any water. Turn 

the power back on. 

ILL1663-A

Once the water level is correct, isolate the control box and 

connect the pump plug.

CONNECTING THE MAGIQTOUCH 

CONTROLLER

®

Refer to the installation manual provided with the MagIQtouch 

Controller for instructions on installing the controller.

The wall control cable plugs into the electronics module - (A). 

(Refer diagram on previous page)

Coolers are supplied with a 20m / 66’ control cable. Longer 

cable lengths are available from Seeley.

Note!

 Where maximum recommended cable lengths are 

exceeded, or cables are not routed in accordance with Seeley 

recommendations, Seeley technical support may not be 

available and the product warranty may be voided.

MAGIQTOUCH CONTROLLER

®

 DISPLAY 

INFORMATION

Diagnosis and cooler operating information can also be viewed 

from the MagIQtouch Controller. Faults are displayed on the 

screen as they occur.

ILL997-C

ILL1664-A

SETUP FOR BLEED FUNNEL

If you installed the bleed funnel instead of the drain valve then 

the cooler will automatically be set to “NO DRAIN CONTROL” 

provided that the shorting plug is installed correctly.
The “NO DRAIN CONTROL” setting can also be set manually 

under the “COOLER” tab in the “WATER MANAGER” menu.

Содержание TBQ





















Отзывы:

Нет отзывов