Breezair TBQ Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 20

Breezair TBQ Скачать руководство пользователя страница 14

14

|

ILL1062-G

ILL1678-A

Connect the water sensor plug (D) and inlet solenoid plug

(C) as shown. If not using a water sensor, then ensure that a

shorting plug is fitted as provided.

CONNECTING THE WATER PUMP

Route the pump cord as shown.

Once the water level is set correctly, isolate the electronics

module and connect the pump plug (F).

Important!

Do not connect the pump plug until the water level

is set.

WARNING!

Do not run the pump while the pad frames are off

and the fan is on.
Once plugs are connected, switch the electronics module on.

Important!

Ensure the flexible splash protection cover is in place.

ILL1061-C

ILL1095-B

LEGEND

A -  Control Cable
B -  Speed Adjustment
C -  Inlet Solenoid
D -

Water Sensor

or Shorting Plug

E -  Drain Valve
F -  Pump
G -  Operation & Fault

code LED’s

Ensure the cables cannot rest in the water once the tank is filled

and plugs are connected in the correct orientation.

ILL1075-C

Route the drain valve cable as shown before connecting it

to the electronics module (E).

ELECTRICAL CONNECTION

cont

«
...
12
13
14
15
16
...
»

Содержание TBQ





















Отзывы:

Нет отзывов