manualshive.com logo in svg

Brave VH0622, Руководство владельца/оператора и по безопасности, Страница: 13 / 48

Поделиться
Скачать
Brave VH0622 Скачать руководство пользователя страница 13

5

.  Lift the front leg and carefully roll the base

unit off the pallet.

6

.  Carefully stand the rail assembly in an

upright, vertical position.

Make sure the rail assembly is standing on
a flat, level area.  If necessary, have a
helper steady the rail to prevent it from tip-
ping over.  The rail assembly weighs
approximately 270 pounds and will cause
bodily injury if it falls on someone.

7

.  Carefully align the base assembly, using

the front leg, with the rail assembly. 

Have someone hold the rail assem-
bly to prevent it from falling during
this part of the assembly.

8

.  Center the rail between the hinge plates

on the base assembly, as shown.  Insert a
1/2-13 x 4-1/2 inch long hex head bolt
through rear top hole of the hinge plates
and rail.  Install and tighten a 1/2-13 lock-
nut.

NOTE:  

To prevent the rail from binding, do

not overtighten the locknut.  This connection
serves as the pivot point for the log splitter
from the vertical to horizontal position.

WARNING

800-350-8739

11

Brave Products, Inc.

Assembly Instructions

Содержание VH0622

















































Отзывы:

Нет отзывов