Bradford White RTG 199 HEN Скачать руководство пользователя страница 7

Страница: 7 / 56

Appliance details

RTG 199 HE – 6 720 811 617 (2016/01)

3.2

Specifications (Technical data)

Approved in US/Canada

Safety devices

• Flame failure device (ionization flame rod sensor)
• Overheat prevention (temperature limiter)
• Inlet temperature sensor
• Outlet temperature sensor
• Back flow temperature sensor
• Exhaust gas temperature sensor

3.3

Unpacking the heater

Before installing the unit, be certain you have the correct heater for
your type of Gas - Propane or Natural Gas.

Identification labels are

found on the shipping box, and on the rating plate which is located on the
right side panel of the cover.

Fig. 2

Rating plate

[A]

Serial number

[B]

Type of gas

Technical characteristics

Units

RTG 199 H

Capacity

Maximum flow rate at a 45 °F
(25 °C) rise

GPM (l/min)

8.3 (31.4)

Maximum flow rate at a 55 °F
(30.6 °C) rise

GPM (l/min)

6.8 (25.7)

Maximum flow rate at a 75 °F
(41.7 °C) rise

GPM (l/min)

5.0 (18.8)

Maximum flow rate at a 90 °F
(50 °C) rise

GPM (l/min)

4.2 (15.7)

Maximum output

BTU/hr (kW)

184,500 (54)

Maximum input

BTU/hr (kW)

199,000 (58.3)

Thermal efficiency (Efficiency
in %)

> 94%

Minimum Input

BTU/hr (kW)

19,900 (5.8)

Temperature Control

Selection range

°F ( °C)

100 - 140 (38 - 60)

Default temperature

°F ( °C)

122 (50)

Stability

°F ( °C)



2 (



Gas Requirement

Gas connection

inches

¾ "

Peak load inlet gas pressure

Propane

water column

8” - 13”

Natural Gas

water column

3.5” - 10.5”

Water

Hot water connection

inches

¾ "

Cold water connection

inches

¾ "

Minimum water flow

GPM (l/min)

0.5 (1.9)

Minimum recommended water
pressure

PSI (bar)

30 (2.07)

Minimum well pressure

PSI

Water valve material

Polymer (PPS)

(Polypropylene

Sulfide)

Connections:

Bottom of heater

Combustion

CO level

ppm



290 (measured)

level (set from factory)

see table 43

Dimensions

Depth

inches (mm)

11 ¼ (286)

Width

inches (mm)

(452)

Height

inches (mm)

30½ (775)

Weight

pounds (kg)

74 (33.5)

Gas types

Natural Gas

Table 3

LP Gas

Voltage

Nominal

V AC

120

Frequency

Amperage

Idle

Operation



2.5

Noise

db (A)

45 - 65

Water protection

X4D

1) To measure Gas Pressure, see Measuring Gas Pressure, chapter 4.15, page 33.

2) Activation varies with inlet water temperatures from 0.5 - 1.6 gallon/minute (1.9

- 6.1 l/m).

3) Protection against water drops.

If appliance is installed at elevations above 2000ft, refer
to chapter 4.3.8 Fan speed adjustment.

Technical characteristics

Units

RTG 199 H

Table 3

Содержание RTG 199 HEN

























































Результаты поиска

Содержание RTG 199 HEN

Отзывы:

Похожие инструкции для RTG 199 HEN

Бренды по названию

Популярные бренды

Bradford White RTG 199 HEN, Инструкция по установке и эксплуатации

Результаты поиска

Содержание RTG 199 HEN

Отзывы:

Похожие инструкции для RTG 199 HEN

Бренды по названию

Популярные бренды