background image

Page 12

 

Bradford White Corp.

Figure 10. Vent Dimensions, 2-Pipe System.

3.3.5 Installations in the Commonwealth of 

Massachusetts

In Massachusetts the following items are required 

if the side-wall exhaust vent termination is less than 

seven (7) feet above finished grade in the area of the 

venting, including but not limited to decks and porches. 

From Massachusetts Rules and regulations 248 CMR 

5.08

1. 

Installation of Carbon Monoxide Detectors

 

At the time of installation of the side wall vented 

gas fueled appliance, the installing plumber or 

gasfitter shall observe that a hard-wired carbon 

monoxide detector with an alarm battery back-up is 

installed on the floor level where the gas appliance 

is to be installed. In addition, the installing plumber 

or gasfitter shall observe that a battery operated or 

hard-wired carbon monoxide detector with an alarm 

is installed on each additional level of the dwelling, 

building or structure served by the side-wall 

horizontally vented gas fueled equipment. It shall 

be the responsibility of the property owner to secure 

the services of qualified licensed professionals 

for installation of hard-wired carbon monoxide 

detectors.

 

a. In the event that the side-wall horizontally vented 

gas fueled equipment is installed in a crawl space or 

an attic, the hard-wired carbon monoxide with alarm 

and battery back-up may be installed on the next 

adjacent floor level.

 

b. In the event that the requirements of the 

subdivision cannot be met at the time of completion 

of installation, the owner shall have a period 

of thirty (30) days to comply with the above 

requirements, provided, however, that during said 

thirty (30) day period, a battery operated carbon 

monoxide detector with an alarm be installed.

2. 

Approved Carbon Monoxide Detectors

 

Each carbon monoxide detector shall comply with 

NFPA 720 and be ANSI/UL 2034 listed and IAS 

certified.

3. 

Signage

 

A metal or plastic identification plate shall be 

permanently mounted to the exterior of the building 

at a minimum height of eight (8) feet above grade 

directly in line with the exhaust vent terminal for 

horizontally vented gas fueled heating appliance 

or equipment. The sign shall read, in print no less 

than one-half (1/2) inch in size: "GAS VENT 

DIRECTLY BELOW, KEEP CLEAR OF ALL 

OBSTRUCTIONS".

4. 

Inspection

 

The state or local gas inspector of the side-wall 

horizontally vented gas fueled appliance shall not 

approve the installation unless, upon inspection, the 

inspector observes carbon monoxide detectors and 

signage installed in accordance with the provisions  

of 248 CMR 5.08(2)(a) 1-4.

3.4  Common Vent Test

NOTE:

 This section does not describe a method for 

common venting Brute Elite units. It describes what 

must be done when a unit is removed from a common 

vent system. Brute Elite units require special vent 

systems and fans for common vent. Contact the factory 

if you have questions about common venting Brute Elite 

units.

When an existing boiler is removed from a 

common venting system, the common venting system is 

likely to be too large for proper venting of the appliances 

remaining connected to it.

At the time of removal of an existing boiler, the 

following steps shall be followed with each appliance 

remaining connected to the common venting system 

placed in operation, while the other appliances 

remaining connected to the common venting system are 

not in operation.

1.  Seal any unused openings in the common venting 

system.

2.  Visually inspect the venting system for proper 

size and horizontal pitch and determine there is no 

blockage or restriction, leakage, corrosion and other 

deficiencies which could cause an unsafe condition.

3.  Insofar as it is practical, close all building doors and 

windows and all doors between the space in which 

the appliances remaining connected to the common 

venting system are located and other spaces of the 

building. Turn on clothes dryers and any appliance 

not connected to the common venting system. 

Turn on any exhaust fans, such as range hoods and 

bathroom exhausts, so they will operate at maximum 

speed. Do not operate a summer exhaust fan. Close 

Optional concentric vent kit sold separately.

Содержание brute elite 125 BLMH





















































Отзывы: