en 7
BPA500: Adjust limits and force
25
1. Open light cover.
2.
Press „P“ and hold it until LED3 starts flashing (1).
3. Press „+“ and hold it until the door is completely open (2).
If neccessary adjust using „-“.
4.
Press „P“ briefly, LED2 starts to glow (3).
5. Press „-“ and hold it until the door is completely closed. The rail must
not bend up (4). If neccessary adjust using „+”.
6.
Press „P“ again briefly. The drive now automatically opens the door
completely and then closes the door completely (5). During this
process the force required by the opener is set.
NOTES:
Do not interrupt the opener during this process otherwise you have to
repeat the whole procedure. In case the door pushes against the door
frame and reverses, the „closed“ limit hasn’t been set properly.
Repeat limit setting and make sure the rail doesn’t bend when setting
the „closed“ limit.
Force adjustment:
When installing the opener the travel (distance between the Open and
Closed position) and the optimal pulling force is learned.
NOTE:
Before any modification to the force adjustment check the door for
proper functioning. The opener is no support for a malfunctioning door.
You can check proper functioning by releasing the opener and opening
and closing the door manually.
26
Test the Safety Reverse System
The safety reverse system test is important. Garage door
must reverse on contact with a 50 mm obstacle laid flat
on the floor. Failure to properly adjust opener may result
in serious personal injury from a closing garage door. Repeat test
once a month and adjust as needed.
OBSTACLE TEST:
Place a 50 mm high obstacle (1) under the garage door on the floor.
Move door downwards. The door must reverse when it comes into
contact with the obstacle. If upon contact the door
stops
, the door does
not move
down
far enough. In this case repeat limit setting. If the door
reverses after contact with the 50 mm high obstacle, remove obstacles
and open and close the door completely once. The door should not go
back, if it reaches the door position „Closed“. If it still reverses both
limits must be reprogrammed.
OPENING TEST: Apply 20 kg to the middle of the door.
The door should not open completely.
The supplied remote control is already programmed.
When purchasing additional remote controls, program the receiver
to match the additional remote control codes.
Program:
1. Press „S“ for 1-2 seconds. LED1 begins to glow (for approx. 10 sec).
2. Briefly press a button of the remote control 2 sec.
3. LED1 goes out. The Code is programmed.
Delete:
All programmed remote control codes will be deleted. Press „S“ and
hold it until LED1 goes out (approx. 8 seconds). All programmed codes
are now erased. Reprogram each remote control you wish to use.
27
28
BPA650, BPA800, BPA1200: Program your
opener and remote / the Wireless push button
(Optional accessory 128EN)
BPA500: Program another remote control
Activate the opener only when door is in full view, free of obstruc-
tion and properly adjusted. No one should enter or leave garage
while door is in motion. Do not allow children to operate push
button(s) or remote(s). Do not allow children to play near the door.
Your garage door opener receiver and one of the buttons remote control
are pre-programmmed. If you purchase additional remote controls, the
garage door opener must be programmed to accept the new remote
code.
Program the Receiver to Match Additional Remote Controls:
Using the yellow round button.
1. Press and release the yellow round button on the opener. The
learn indicator light will glow steadily for 30 seconds (1).
2. Within 30 seconds, press and hold the button on the hand-held
remote that you wish to operate your garage door (2).
3. Release the button when the opener light blinks once. It has
learned the code. Now the opener will operate when the remote
control push button is pressed. If you release the remote control
push button before the opener light flashes, the opener has not
learned the code.
To Erase all Remote Control Codes
To deactivate any unwanted remote, first erase all codes: Press and
hold the yellow round button on opener until the learn indicator light
goes out (approximately 10 seconds). All previous codes are now er-
ased. Reprogram each remote or keyless entry you wish to use.
