background image

Remove the Old Unit from the Dashboard

DIN Front Mount

DO NOT DISCONNECT WIRES
AT THIS TIME!

2.  Insert  the  keys  supplied  with  the 

old unit into both sides of the unit 
as  shown  in  figure  below  until 
they click. Pull to remove the old 
unit from the dashboard.

1.  Remove  the  outer  trim  frame.

INSTALLATION

Tools for Installation

2 removal wrenches are supplied for taking out the old unit and place with this 
brand name car radio. The following tools and supplies may also be needed for 
the installation:
Tools  for  Installation:  Philips  Screw-drivers  /Machine  Screws  /Wire  Stripper 
/Wire Cutter /Hammer /Pencil /Electrical Tape /Electric Drill
Supplies for Installation: Machine Screws /Crimp Connectors /14 Gauge Wire for 
Power Connections /14-16 Gauge Speaker Wires

The above are not supplied.

Before you install

Automotive audio equipment installations can be challenging even to the most 
experienced  of  installation  technicians.  We  strongly  recommend  that  this  unit 
should be professionally installed by a VAT registered installer (this is a require-
ment to validate the warranty).
IMPORTANT: Remove the two transport screws from the top fo the unit before 
installing.  

Mark Polarity of the Speaker Wires

Marking  the  polarity  of  the  speaker  wirers  will  make  it  easier  to  connect  the 
existing speakers to your car radio. Consult wiring diagram of existing head unit 
before disconnecting any wires. If you are not positive of the polarity of the exist-
ing wires from the speakers to the head unit, install new wires. 
1. While the old unit is playing, disconnect the wires from one speaker. 
2. Take a length of masking tape and fold it around the wire so it forms a flag.
3. On the masking tape mark the polarity of the speaker wires (+&-), as well as 
left or right, and front or rear.
4. Double check that you marked the first speaker correctly by checking that the 
speaker wires are the same at the head unit.
5. Repeat this procedure for all of the speakers.
6. Mark the power, ground, and any other wires also.
 

Содержание BV7254















Отзывы: