background image

 

6 720 220 380

Subject to change without prior notice                                      Revised 06-13

6

TsTbT4h2CP series

insTallinG The TsTbT4h2CP 

ThermosTaT series

Caution

A trained, experienced technician must install this 
product. Carefully read these instructions. You could 
damage this product or cause a hazardous condition if 
you fail to follow these instructions. See the product 

specifi cations at the end of this manual prior to installing.

wall loCaTions

Do not install thermostats in locations that are:

•  On an exterior Wall

•  In direct sunlight

•  Where there may be concealed chimneys or pipes 

behind the wall

•  Close to a window or door leading outside

•  Close to objects radiating heat such as fi re places, 

lighting, space radiators, or any other applicance

•  In areas that do not require conditioning

•  In dead spots or where drafts can occur (behind doors 

or in corners)

•  Close to hot or cold air ducts

Caution

Pick an installation location that is easy for the 
user to access. The temperature of the location 
should be representative of the building.

mounting the Thermostat

First, separate the thermostat and sub-base using a fl at 
blade screw driver as shown below.

Screw driver

Rotate the screw driver tip so the thermostat separates 
from the sub-base and then pull the thermostat away from 
the sub-base.

Align the 4 tabs on the subbase with corresponding slots 
on the back of the thermostat or base module. Then push 
gently until the thermostat or base module.

Caution

To insure a solid fi t between the thermostat 

and the subbase: 

1.  Mount subbase to a fl at wall 

2.  Use screws provided

3.  Drywall anchors should be fl ush with the wall

4.  Wires should be pushed into the wall

insTallinG The Trm reCeivinG module

TRM stands for Transmitting and Receiving Module. The 
TRM communicates with the  TSTBT4H2CP Thermostat 
Series using the MODBUS protocol and then translates 
the MODBUS protocol to pulses and relays these signals 
to the HVAC equipment. 

The Receiving Module can be installed adjcent to or 
within the HVAC equipment.

Secure to wall or equipment

with screws at top and bottom.

Remove these screws (4)

to access terminals.

Descriptive Part#

TSTB-TRM--6--A

P/N 7738002948

Receiving Module

24VAC, 2VA, No Load

Made in USA

COM

HVAC

There are two LED lights on the TRM. One is the COM 
light which blinks green when communication is 
happening between the TRM and the thermostat. This 
light will normally blink about every 10 seconds as the 
thermostat and TRM are in constant communication for 
status updates. If communication is lost for more than 10 
minutes, the COM LED will become red. A certifi ed 
licensed technician should be called to service the system 
if this occurs.

The other LED is labeled HVAC. This light indicates if the unit 
is actively heating or cooling. If the unit is cooling, then the 
LED is yellow, if the unit is in heating, then the LED is red. If 
the thermostat is satisfi ed, then the LED if off.

 

installing the Thermostat

Содержание TSTBT4H2CP-M--A

























Отзывы: