Bosch SM Split CS Series Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 44

Bosch SM Split CS Series Скачать руководство пользователя страница 37

Decommissioning Information

|

37

SM Split CS Series Heat Pump

8733825873 (2020/05)

SM Split CS Series Heat Pump

Subject to change without prior notice

DECOMMISSIONING INFORMATION

Only trained and qualified technicians are allowed

to decommission and dispose of equipment

following the requirements of the Local Authority

Having Jurisdiction (AHJ).

Protecting the Environment

Components

Refrigerant

Hazardous Waste

WARNING

: Decommissioning of this

equipment can be hazardous due to system
pressure and electrical components. Only
trained and qualified personnel should
install, repair, service, or disconnect the
equipment.

By  disposing  of  this  product  correctly  you
will  help  ensure  that  the waste  undergoes
the  necessary  treatment,  recovery,  and
recycling,  thus  preventing  potentially
negative  effects  on  the  environment  and
human health, which could otherwise arise
due to inappropriate waste handling.

Many parts in the Heat Pump can be fully
recycled at the end of the product life.
Contact

your

city

authorities

for

information about the disposal of
recyclable products.

At  the  end  of  the  service  life  of  this
appliance,  and  prior  to  its  environmental
disposal,  a  person  qualified  to  work  with
refrigerant  circuits  and

®

Refrigerant Recovery/Recycling Equipment
must recover the refrigerant from within the
sealed system.

Some components in the Heat Pump may be
considered as hazardous waste, such as
batteries. For their disposal contact your
local household hazardous waste collection
site.

«
...
35
36
37
38
39
...
»

Содержание SM Split CS Series













































Отзывы:

Нет отзывов