Bosch SM Split CS Series Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 44

Bosch SM Split CS Series Скачать руководство пользователя страница 15

Water Quality Table

|

15

SM Split CS Series Heat Pump

8733825873 (2020/05)

SM Split CS Series Heat Pump

Subject to change without prior notice

Electrical

Refer to electrical component box layout. (See Fig. 5)

The unit is provided with a concentric knock-out

for attaching common trade sizes of conduit.

Route power supply wiring through this opening.

Always connect the ground lead to the grounding

lug provided in the control box and power leads to

the line side of compressor contactor as indicated

on the wiring diagrams starting on page #38.

Fig. 5 Electrical Component Box Layout

[1] Compressor Contactor
[2] Unit Protection Module (UPM)
[3] Low-Voltage Terminal Block
[4] Pump/Valve Relay
[5] Capacitor
[6] SmartStart Assist (Field-Installed Accessory)
[7] Grounding Lug

WARNING: UNIT OPERATION AND SAFETY
HAZARD

Field wiring must comply with local and
national electric codes.

WARNING: UNIT OPERATION AND SAFETY
HAZARD

Properly-sized fuses or HACR circuit
breakers must be installed for branch
circuit protection. See the unit nameplate
for maximum fuse or breaker size.

WARNING: UNIT OPERATION AND SAFETY
HAZARD

Power to the unit must be within the
operating voltage range indicated on the
unit’s nameplate or on the performance
data sheet.

NOTICE:

Operation of unit on improper line

voltage or with excessive phase imbalance
will be hazardous to the unit, constitutes
abuse and may void the warranty.

«
...
13
14
15
16
17
...
»

Содержание SM Split CS Series













































Отзывы:

Нет отзывов