Bosch SM Split CS Series Скачать руководство пользователя страница 2

Страница: 2 / 44

SM Split CS Series Heat Pump

SM Split CS Series Heat Pump

8733825873 (2020/05)

Subject to change without prior notice

Document Conventions .......................................................3

Key to Symbols............................................................ 3

Safety Warnings..................................................................3

Model Nomenclature ...........................................................4

CS/Air Handler Pairing ........................................................5

SM Split CS Standard Package .............................................6

General Description ..................................................... 6
Moving and Storage ..................................................... 6
Initial Inspection .......................................................... 6

Unit Installation ..................................................................7

Location Selection...............................................................7

Condensing Section Location ........................................ 7
Air Handler Location..................................................... 7

Installation .........................................................................7

Condensing Section Installation..................................... 7
Condensate Drain........................................................ 8
Water Piping ............................................................... 8

Refrigerant Lines ................................................................9

Linear vs. Equivalent Line Length ................................... 9
Connecting Refrigerant Lines......................................... 9
Additional Adjustments Required when Pairing SM Split CS
with BVA2.0 and BMAC .............................................. 11

Water Quality Table...........................................................14

Electrical .................................................................. 15

Safety Devices and the UPM Controller...............................16

Typical System Setup ........................................................19

Specific Application Considerations ............................. 20
Well Water Systems ................................................... 20
Cooling Tower/Boiler Systems..................................... 20
Geothermal Systems.................................................. 20

Post-Installation System Checkout.....................................21

System Operation .............................................................21

Unit Start-up.....................................................................21

Sequence of Operation ......................................................21

Standard Factory-Installed Components.............................23

Pump/Valve Relay...................................................... 23

Field-Installed Accessories ................................................23

Flow Proving Switch (DPS) ......................................... 23
SmartStart Assist Specifications.................................. 24
SmartStart Assist Modes of Operations......................... 24

Check-Out Sheet ...............................................................27

Troubleshooting................................................................28

SmartStart Assist Troubleshooting ............................... 30
SmartStart Assist Flashing Sequence............................ 30
UPM LED Status Indicator (Blink Code) Information........ 31

Compressor Ohms .....................................................31

Operating Temperatures and Pressures.............................. 32

Maintenance .................................................................... 36

Water Side Pressure Drop in PSIG ................................36

Decommissioning Information ........................................... 37

Protecting the Environment .........................................37

Wiring Diagrams ............................................................... 38

Dimensional Drawings....................................................... 39

Terminology ..................................................................... 40

Acronyms .................................................................40
Terms.......................................................................40

Notes ............................................................................... 41

Содержание SM Split CS Series













































Результаты поиска

Содержание SM Split CS Series

Отзывы:

Похожие инструкции для SM Split CS Series

Бренды по названию

Популярные бренды

Bosch SM Split CS Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание SM Split CS Series

Отзывы:

Похожие инструкции для SM Split CS Series

Бренды по названию

Популярные бренды