Bosch SHI 4302 Скачать руководство пользователя страница 88

Страница: 88 / 144

VIII.

Troubleshooting

Heater

–

Replacing Older UC/06 NLA Heaters

Some heater assemblies for old index UC/06 models aren’t
available -- #

264463

(for

SHU 3000/4000

models) & #

269255

(for

SHU 3030/3130

models). Similar heater

assemblies for other index UC/06 models can be used when
thermostats are installed, flow switches are replaced and
aqua sensors are removed – use #

263869

(used on

SHU

53/68

models) or #

264462

(used on

SHU 33/43/99

models).

Remove

aqua

sensor

Push latches to remove NTC,
then replace with appropriate
thermostat (& o-ring) for the
particular model.

# 069796

# 175711

Must replace 2-
terminal flow switch
# 175711 with 3-
terminal # 069796.

HINT:

Do not use softer

bearing heater assemblies
(UC/11 & later) such as #
480317 on older UC/06
models since the sump,
circulation pump, base and
heater clamps/gaskets
have to be replaced as
well for the heaters to fit.

HINT:

Remove aqua sensors from heater

assemblies before installation as aqua sensors aren’t
used and have no wires to be connected to.

NOTE:

Individual heating elements aren’t available.

Use 263869 or 264462 heater assemblies only.

165384 thermostat for

SHU 3030/3130 models

168575 thermostat for

SHU 3000/4000 models

Содержание SHI 4302

















































































































































Результаты поиска

Содержание SHI 4302

Отзывы:

Bosch SHI 4302, Руководство пользователя, Страница: 88 / 144

Результаты поиска

Содержание SHI 4302

Отзывы: