Bosch SHI 4302 Скачать руководство пользователя страница 40

Страница: 40 / 144

VI.

Component Access/Replacement

Control Modules

Disassembly (1)

Control modules are easily removed from
fascia panels by bending console tabs.

(SHU 9922 shown)

Remove fascia panel by removing T-20
Torx inner door screws.

Disconnect wire harnesses from module
after noting connector locations.

Pry out metal console tabs holding
module to console.

Carefully pry back plastic tabs, then slide
module from console.

Removing door screws

Removing fascia panel

Viewing control module

Disconnecting wires

Bending back tabs

Sliding module out

Console without module

NOTE:

Control modules

for non-integrated models
look differently and have
different tabs, but are
removed using the same
procedure.

NOTE: Control modules
for non-integrated models
look differently and have
different tabs, but are
removed using the same
procedure.

Содержание SHI 4302

















































































































































Результаты поиска

Содержание SHI 4302

Отзывы:

Похожие инструкции для SHI 4302

Бренды по названию

Популярные бренды

Bosch SHI 4302, Руководство пользователя

Результаты поиска

Содержание SHI 4302

Отзывы:

Похожие инструкции для SHI 4302

Бренды по названию

Популярные бренды