Bosch SHI 4302 Скачать руководство пользователя страница 75

Страница: 75 / 144

VIII.

Troubleshooting

Circulation Pump

Water Switch Pump Nuisance Tripping (1)

There have been some nuisance tripping of thermal motor protectors on
three-winding circulation pumps for use with water switches (#

239129

To prevent nuisance tripping, use pumps with upgraded thermal
protectors (#

437345

). If upgraded pumps (#

437345

) aren’t available,

use original circulation pumps (#

239129

) with new (PTC) motor starters

designed to prevent nuisance tripping (#

423023

IMPORTANT:

Using new & original

pumps & motor starters:

•

Use “new" circulation pump #

437345 (with 135ºC OVLP) only

with "original" motor starter #

182318 (4.7 – 4.8

Ω

•

Use “original" circulation pump #

239129 (with 120ºC OVLP) only

with "new" motor starter # 423023

(15

Ω

TECH NOTES:

New motor starter # 423023 (15

Ω

) has a larger resistance to limit current

draw through pump motor start windings. Winding temperatures are reduced, but starting

torque is reduced as well. So, new motor starters (# 423023) should never be used with new

circulation pumps (# 437345).

HINTS:

Typical repairs will involve either replacing “original" circulation pump # 239129 with

“new" circulation pump # 437345 (preferred) or replacing "original" motor starter # 182318

with "new" motor starter # 423023.

TECH TIPS:

All circulation pump motors use auto-reset thermal protectors. Once motor

windings cool below a preset temperature, protectors reset and pumps will work again. If

thermal protectors fail to reset, replace pumps.

Содержание SHI 4302

















































































































































Результаты поиска

Содержание SHI 4302

Отзывы:

Похожие инструкции для SHI 4302

Бренды по названию

Популярные бренды

Bosch SHI 4302, Руководство пользователя

Результаты поиска

Содержание SHI 4302

Отзывы:

Похожие инструкции для SHI 4302

Бренды по названию

Популярные бренды