Bosch SHI 4302 Скачать руководство пользователя страница 44

Страница: 44 / 144

VI.

Component Access/Replacement

Control Modules

–

Apexx

Control Module Disassembly (2)

To remove right & left side panels

(where necessary)

Remove two T-20 Torx side panel screws through holes in left &
right trim strips

(1)

Carefully slide trim strips up and out of dishwasher

(2)

. If side

panels are removed carefully to avoid damaging trim strips, then
trim strips don’t need to be removed.

Lift side panels up and out from dishwasher

(3)

. Panels can be

removed with trim strips. Although removing the left side panel
isn’t necessary for access, it does allow the right side of the tank
to be blocked upward.

Removing trim strip screws

Removing trim strips

Removing side panels

HINT: Apexx control modules cannot
be checked or have resistances
measured from the front of
dishwashers.

HINT: It may be possible to reach behind
modules without blocking up tanks. If not,
then follow these instructions to block up
tanks.

Содержание SHI 4302

















































































































































Результаты поиска

Содержание SHI 4302

Отзывы:

Bosch SHI 4302, Руководство пользователя, Страница: 44 / 144

Результаты поиска

Содержание SHI 4302

Отзывы: