Bosch SHI 4302 Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 144

background image

75

VIII.

VIII.

Troubleshooting

Troubleshooting

Circulation Pump

Circulation Pump

–

–

Replacing Impellers (1)

Replacing Impellers (1)

Occasionally, a circulation pump impeller can stick if a dishwasher hasn’t been used for a
long time. Impeller ceramic rings and carbon rings had been changed (during January,
2001) to reduce or eliminate impeller sticking (ceramic rings are located around shaft on
rear of impeller).

For temporary repairs when impeller replacement isn’t possible, impellers can be loosened
by rotating them (through the sump) using an

8mm

nut driver (impellers should be replaced

shortly thereafter when repairs are possible).

NOTE:

Upgraded spacers and ceramic

rings (January, 2001 and later) provide
lower friction and less contact area,
preventing impeller sticking when
dishwashers haven’t been used for long
periods of time.

HINTS:

Upgraded impellers (with upgraded
ceramic rings) and carbon rings fit
both old 263835 and new 266511
(softer bearing) circulation pump
motors (and corresponding pump
housings).

Check color of impeller ceramic
rings as shown below to determine
upgraded (January, 2001 & later) and
old (December, 2000 & before) style
rings.

Make sure black spacer is reinstalled
-- failure to reinstall spacer can
cause motor to bind.

INSTRUCTIONS FOR LOOSENING
IMPELLER:

To loosen stuck impeller, access sump by
removing microfilter and sump screen.
Insert an

8mm

nutdriver through sump

hole to impeller -- place nutdriver onto
8mm stud on impeller and carefully rotate
impeller clockwise until it becomes free
(at least two full revolutions).

Sump

8 mm nutdriver

Impeller

Access port to
impeller through
sump

HINT:

Impeller ceramic ring color code:

Bright white --

upgraded ring

Pink --

upgraded ring

Dull yellow/cream --

old ring (impeller

should be replaced)

Dull white (off white) --

old ring (impeller

should be replaced)

UPGRADED

OLD STYLE

NOTE:

Impellers should be replaced

(instead of loosened) whenever
possible. Loosening impellers should
be done only on a temporary basis.

«
...
75
76
77
78
79
...
»

Содержание SHI 4302

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для SHI 4302

Бренд: Sammic Страницы: 48

Бренд: VESTEL Страницы: 16

Бренд: Fisher & Paykel Страницы: 19

Бренд: V-ZUG Страницы: 6

Бренд: Daewoo Страницы: 36

Бренд: arcelik Страницы: 60

Бренд: TdA electronics Страницы: 12

Бренд: Maytag Страницы: 36

HG6085C13J7609DW

Бренд: Hanseatic Страницы: 76

Бренд: Indesit Страницы: 84

Бренд: Hotpoint Страницы: 16

Бренд: Hoonved Страницы: 21

Бренд: Haier Страницы: 10

THERMOCOOL TLSA13B

Бренд: Haier Страницы: 18

Бренд: Haier Страницы: 20

Бренд: Haier Страницы: 25

Бренд: Haier Страницы: 32

Бренд: Electrolux Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды