Bosch SHE43P15 Скачать руководство пользователя страница 7

Страница: 7 / 42

3.2

Reset (“Cancel – drain”)

To reset, push

Cancel-Drain

Cancel-Reset

buttons at the same

time.

3.3

Changing basic features (on selected units)

On some models, features can be changed on the fascia panel.

3.3.1 Extra dry heat

With

Extra Dry Heat

, the temperature of the rinse water can be

raised and the drying time increased for improved drying.



Turn the dishwasher off and then push and hold the left

Cancel Reset

button while turning the dishwasher on –

release buttons when the display shows “

” or “

”.



Pushing

the

left

Cancel Reset

button changes the setting –

choose “

” to turn it on and choose “

” to turn it off. Push the

on/off button to save the setting.

3.3.2 End of cycle tone

The

End of cycle tone volume

can also be changed.



Turn the dishwasher off and then push and hold the right

Cancel Reset

button while turning the dishwasher on –

release buttons when a tone sounds or the right

Cancel Reset

button LED lights up.



Pushing

the

right

Cancel Reset

button changes the setting –

push it until the tone is at the desired volume (or the tone
stops if it’s to be turned off). Push the on/off button to save
the setting.

3.4

Entering special programs and coding

Controls contain codes for sales demo mode, factory tests,
customer service test program, dishwasher configuration and
error codes. Consult test programs and error codes for your
dishwasher before using the codes listed in this manual.

702_58300000148618_ara_en_a

Page 7 of 42

Содержание SHE43P15











































Результаты поиска

Содержание SHE43P15

Отзывы:

Похожие инструкции для SHE43P15

Бренды по названию

Популярные бренды

Bosch SHE43P15, Руководство по ремонту

Результаты поиска

Содержание SHE43P15

Отзывы:

Похожие инструкции для SHE43P15

Бренды по названию

Популярные бренды