Bosch SHE43P15 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 42

background image

3. Remove terminal blocks (for two-piece harnesses) or

base-mounted controls from base when necessary.

4.

Remove water valve

-- see section 5.1.1.1.

5. Disconnect J-box ground wire and pull wires out of J-box.

6.  Pull out inlet hose from sump.
7.  Disconnect front and rear screws holding base and tank.
8.  Carefully pull base away from tank and sump.

5.4.3 To remove heater & NTC

1. Loosen pump - heater hose clamp and remove two (2) T-

20 Torx screws holding heater assembly to sump.

2. Carefully pull heater from sump & pump. The heater

comes as an assembly with housing & gasket.

3. Note connections, remove NTC cover and disconnect

wires from heater, flow switch, NTC & Hi-Limit.

4. Push NTC latches and lift NTC from heater.
5. To remove flow switch, carefully pry housing away from

switch (until tabs clear switch), then snap switch out.

TIP:

If needed, use rinse-aid to lubricate gaskets to make it

easier to assemble heater to sump and pump.

702_58300000148618_ara_en_a

Page 33 of 42

«
...
31
32
33
34
35
...
»

Содержание SHE43P15











































Отзывы:

Нет отзывов

Похожие инструкции для SHE43P15

Бренд: Haier Страницы: 38

Бренд: Panasonic Страницы: 44

Бренд: Asko Страницы: 24

Бренд: Smeg Страницы: 21

Бренд: Metos Страницы: 52

Бренд: Blomberg Страницы: 40

Бренд: Hotpoint Страницы: 16

Бренд: NewAir Страницы: 24

Бренд: Daewoo Страницы: 26

Бренд: GEAppliances Страницы: 16

Бренд: Euromaid Страницы: 31

Бренд: Amica Страницы: 28

Бренд: Ariston Страницы: 12

Бренд: Samsung Страницы: 64

Бренд: Samsung Страницы: 68

Бренд: Samsung Страницы: 112

WW9 J5 6 Series

Бренд: Samsung Страницы: 272

Бренд: Samsung Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды