background image

 
 

 

 

 

5.3.3  Display modules 

Some dishwashers have separate 3-digit display modules 
mounted on the front of fascia panels. 

Tools needed:  T-20 Torx & flat blade screwdrivers

5.3.3.1 

To remove / install display modules 

1. 

Remove outer door & fascia panel

 – see section 5.3.1. 

2. Disconnect wire harness and rotate display out from 

display holder.  Confirm latches are intact. 

3. To install display, route display wire harness through 

console opening, push harness onto pushbutton carrier 
wire guide & connect terminal. 

4.  Insert display into top latches, then push bottom of display 

up and rotate it into bottom latches. 

  

  

 

5.4 

Heaters 

The heater & NTC can be accessed or measured from the right 
side of the dishwasher, but can only be removed by dropping the 
entire base (by flipping the dishwasher on its back) since they are 
wedged underneath the tank.    

5.4.1  For access to heaters & NTC’s 

Tools needed:  T-20 Torx screwdriver & pliers

1. 

Remove outer door

 – see section 5.2.1 

2. 

Remove toe kick

 – see section 5.2.2. 

3. 

Remove right/left side panels

 – see section 5.2.3. 

4. 

Raise right side of tank

 – see section 5.2.4. 

5.4.2  To separate base from tank 

1.  Carefully lay dishwasher upside-down. 
2.  Carefully pull door springs out from base. 

702_58300000148618_ara_en_a 

Page 32 of 42 

  

  

 

Содержание SHE43P15











































Отзывы: