Bosch SHE43P15 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 42

background image

4.1.9.2

Using hinge slider (sliding pulley)

During FD 8910, hinge pulleys were replaced with hinge sliders
(sliding hinge pulleys). Instead of rolling over rotating pulleys,
door spring cords slide over pulley sliding surfaces. The sliding
surfaces provide better control than rotating pulleys (i.e. reduces
possibility of doors slamming closed or falling open).

618605

sliding hinge pulley kit replaces all prior pulleys, including

426067

. The kit consists of (2) sliding pulleys and (2) cords

which are installed in the field.

4.1.10 Hinge bushing

Hinge bushings hold doors in place (at hinges). Older hinge
bushings used a separate lock. Newer hinge bushings have
latches holding doors in place. Bushings have different
diameters and can’t be mixed. Bushings can be changed as long
as matching hinge levers are used.

Replacement Hinge Levers and Bushings

Side Part #

Description

Replaced by

Description

Left

492033

Lever (14mm)

165296

Lever + bushing (15mm)

Left

488250

Bushing (14mm)

165296

Lever + bushing (15mm)

Left

263115

Lever + bushing (14mm)

165296

Lever + bushing (15mm)

Right

492034

Lever (14mm)

165296

Lever + bushing (15mm)

Right

488250

Bushing (14mm)

165296

Lever + bushing (15mm)

Right

263119

Lever + bushing (14mm)

165296

Lever + bushing (15mm)

702_58300000148618_ara_en_a

Page 19 of 42

«
...
17
18
19
20
21
...
»

Содержание SHE43P15











































Отзывы:

Нет отзывов

Похожие инструкции для SHE43P15

Бренд: Haier Страницы: 38

Бренд: GE Страницы: 36

Бренд: Saba Страницы: 124

Бренд: Silverline Страницы: 88

Бренд: Smeg Страницы: 29

Бренд: Smeg Страницы: 38

Бренд: Supera Страницы: 15

Бренд: Smeg Страницы: 28

Бренд: Samsung Страницы: 56

Бренд: Samsung Страницы: 68

Бренд: Samsung Страницы: 68

Бренд: Samsung Страницы: 80

Бренд: Samsung Страницы: 128

Бренд: Samsung Страницы: 220

Бренд: Samsung Страницы: 316

Бренд: Samsung Страницы: 56

WW75H5200E Series

Бренд: Samsung Страницы: 88

Бренд: Samsung Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды