Bosch Rexroth ID 200/C-PDP Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 84

background image

Communication with ID 200/C-PDP 35/84

3 842 540 399/2016-11, MIT: ID 200,

Bosch Rexroth AG

7.3 Communication via the PROFIBUS DP

7.3.1

PROFIBUS DP communication parameters (device master data file) for

the ID 200/C-PDP

The device master data file name for the ID 200/C-PDP communication module
with PROFIBUS DP interface is: “RXL_0136.gsd”

The following data field sizes (modules) are pre-defined in the device master data
file:

Read/write access:

“In / Out 4 Words” transmits 1 double word Input and output

(32 bit)

user data

“In / Out 6 Words”   transmits   2 double words  “
“In / Out 8 Words”   transmits   3 double words  “
“In / Out 10 Words”   transmits   4 double words  “
“In / Out 12 Words”   transmits   5 double words  “
“In / Out 14 Words”   transmits   6 double words  “
“In / Out 16 Words”   transmits   7 double words  “
“In / Out 32 Words”   transmits  15 double words “

Read access only:

“4 In / 2 Out Words” transmits 1 double word input user data

(32 bit)

“6 In / 2 Out Words”  transmits   2 double words  “
“8 In / 2 Out Words”  transmits   3 double words  “
“10 In / 2 Out Words”

transmits

4 double words

“

“12 In / 2 Out Words”

transmits

5 double words

“

“14 In / 2 Out Words”

transmits

6 double words

“

“16 In / 2 Out Words”

transmits

7 double words

“

“32 In / 2 Out Words”

transmits

15 double words

“

Select a module from the pre-defined modules. When selecting a module, ensure
that the data field size is adequate for the write/read commands used depending on
the “Number of words” parameter.

The “Data Hold Time” and “Diagnosis interrupt” are saved in the device master
data file. These values can be changed via the PROFIBUS slave properties.

The Data Hold Time is the time after which the identification system can overwrite
the input data field. This time must be selected so that it is larger than the cycle time
of the control. If two data carriers are read immediately one after the other, the code
of the data carrier read first remains in the input data field for the set time. After this
time, the code of the second data carrier is entered.
The diagnosis interrupt defines whether an interrupt is triggered via PROFIBUS if a
new diagnostic message occurs. The diagnosis interrupt can be switched on and off.

EN

GLISH

«
...
33
34
35
36
37
...
»

Содержание Rexroth ID 200/C-PDP





















































































Отзывы:

Нет отзывов

Похожие инструкции для Rexroth ID 200/C-PDP

Бренд: KELCO Страницы: 36

Бренд: Wavelink Страницы: 69

Бренд: BADLANDS Страницы: 2

Бренд: Hama Страницы: 7

Бренд: Hama Страницы: 44

Бренд: RadioMaster Страницы: 10

Бренд: K&K Страницы: 6

Бренд: NAiS Страницы: 144

Бренд: LLURIA Страницы: 2

Бренд: Nemesis Страницы: 6

Бренд: GI.BI.DI Страницы: 60

DuoControl Signal 111

Бренд: Tormatic Страницы: 3

Бренд: SMC Networks Страницы: 10

Бренд: Westfalia Страницы: 18

Бренд: UniPOS Страницы: 6

Бренд: Comunello Страницы: 13

Smart Bias-T SBT-6962690-FFM

Бренд: Amphenol Страницы: 2

THRUSTER COMMAND TCD 1022 E

Бренд: Quick Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды