manualshive.com logo in svg

Bosch Rexroth Hagglunds CA 10, Руководство по установке и обслуживанию

Поделиться
Скачать
Bosch Rexroth Hagglunds CA 10 Скачать руководство пользователя страница 34

 Commissioning 33/52

Bosch Rexroth Mellansel AB

,  Installation and maintenance manual, Hägglunds CA 10 - CA 40, RE 15354-WA/04.2015

8  Commissioning

NOTice

Dirt particles!

A not run-in motor in combination with dirt particles in the oil can badly affect the 
sliding surfaces in the motor. This is valid during the first 100 hours.

 

▶

The Hägglunds radial piston hydraulic motor must be installed and commisioned 
in a clean condition.

8.1  Commissioning

Check the following points before commissioning the motor, i.e. before starting the 

first time:

 

•

Make sure that all fluids has been removed from the motor to prevent accidental 
mixing with the hydraulic fluid used in the system.

 

•

Check that the motor is connected to give the correct direction of rotation, see 

7.3.5: Hydraulic ports

 and 

7.3.6: Direction of rotation of motor shaft.

 

•

Select the hydraulic fluid in accordance with the recommendations, 

see 

15.1.4: 

Hydraulic fluids 

and 

data sheet RE 15414, Hydraulic fluid quick reference.

8.1.1 

Oil filling

1. 

Fill the motor housing with hydraulic fluid via a filter into the drain outlets D1, 

D2 or the vent hole (depending on how the motor is mounted), see 

Table 5: Oil 

volume.

2.  Check the drain line to ensure that excessive pressure does not build up in the 

motor case; see chapter 

7.2: Installation conditions

 and 

7.3.3: Draining and venting 

the motor

.

3.  Check that the motor is protected from overloads, see chapter 

15.1.1: Motor data

.

4.  Check that the charge pressure conforms to the charge pressure curve, see 

chapter 

15.1.2: Recommended charge pressure

.

5.  Check that all hydraulic couplings and plugs are properly tightened to prevent 

leakage.

Содержание Rexroth Hagglunds CA 10






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды