manualshive.com logo in svg

Bosch Rexroth Hagglunds CA 10, Руководство по установке и обслуживанию

Поделиться
Скачать
Bosch Rexroth Hagglunds CA 10 Скачать руководство пользователя страница 20

 

Transport and storage

 

19/52

Bosch Rexroth Mellansel AB

,  Installation and maintenance manual, Hägglunds CA 10 - CA 40, RE 15354-WA/04.2015

Table 5: Oil volume

Motor

Oil volume approx.
litres

US gal.

CA 10

0.7

0.19

CA 20

1.0

0.26

CA 30

1.1

0.29

CA 40

1.2

0.32

Fig. 8: Filling the motor with oil

6.2.2  Storing for extended periods or in uncontrolled environment

NOTice

Insufficient cleanliness!

Risk of damage to equipment.

 

▶

Take extreme care to ensure that no contamination enters the motor.

If the motor is stored for more than 3 months in an uncontrolled environment or 

more than 12 months in a controlled environment, it must be filled with oil. 

 

1 

Place the motor as shown in 

Fig. 7: Hägglunds CA 10 - CA 40 standing on a flat 

surface

, alt.A) Standing with shaft horizontal.

2 

Fill the motor with filtered oil in the following order: D1, A1, C1. 

 

NOTE! 

See 

Table 5: Oil volume

.

3 

Seal connections A1 and C1 with the plugs fitted to the connection surface at 

delivery. Check that the O-rings or rubber seals are in position on the plugs.

4 

Fit the plug to D1.

5 

Position the motor as shown in 

Fig. 7: Hägglunds CA 10 - CA 40 standing on a flat 

surface

, alt. A) Standing with shaft horizontal. or B) Standing with shaft vertical.

DD00070796

Содержание Rexroth Hagglunds CA 10






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды