manualshive.com logo in svg

Bosch Rexroth Hagglunds CA 10, Руководство по установке и обслуживанию

Поделиться
Скачать
Bosch Rexroth Hagglunds CA 10 Скачать руководство пользователя страница 26

 Installation 25/52

Bosch Rexroth Mellansel AB

,  Installation and maintenance manual, Hägglunds CA 10 - CA 40, RE 15354-WA/04.2015

7.3.3  Draining and venting the motor

Horizontal mounting 

When the motor is installed with the shaft in the horizontal plane, the highest of the 
two drain outlets D1 or

 

D2 must always be used (see 

Fig. 12: Draining and venting, 

horizontal mounting and Fig. 13: Positioning of drain connection / Maximum angle of 
shaft page 26) 

Drain line must be connected to the tank with a minimum of restrictions, to ensure 
that the maximum case pressure is not exceeded.

For manintenance, see chapter 

10.2: Maintenance plan.

Fig. 12: Draining and venting, horizontal mounting

The case drain fluid must 

be directed to reservoir via 
the highest located drain 
connection, D1 or D2

Drain connection
D1

Drain connection
D2

DD00069615

Содержание Rexroth Hagglunds CA 10






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды