manualshive.com logo in svg

Bosch Rexroth Hagglunds CA 10, Руководство по установке и обслуживанию

Поделиться
Скачать
Bosch Rexroth Hagglunds CA 10 Скачать руководство пользователя страница 30

 Installation

 

29/52

Bosch Rexroth Mellansel AB

,  Installation and maintenance manual, Hägglunds CA 10 - CA 40, RE 15354-WA/04.2015

Fig. 15: Connection side of the motor

7.3.5   Hydraulic ports

When using (thick wall) piping and in frequent reversal drives, it is recommended 

to fit flexible hoses between the motor and piping to avoid damage due to vibration 

and to simplify installation of the motor. The length of the hoses should be kept fairly 
short.

Table 13: Ports

Connection

Description

Dimension

Remarks

A1

Main connection

G 1“

Normally plugged at delivery.
If A is used as the inlet, the motor 
shaft rotates counter clockwise, 
viewed from the motor shaft side.

C1

Main connection

G 1“

Normally plugged at delivery.
If C is used as the inlet, the motor 
shaft rotates clockwise, viewed from 
the motor shaft side.

A2

Alternative main 
connection

G 1“

Normally plugged at delivery.

C2

Alternative main 
connection

G 1“

Normally plugged at delivery.

D1

Drain connection

G 1/2“

Normally plugged at delivery.

D2

Alternative drain 
connection

G 1/2“

Normally plugged at delivery.

DD00068761

Содержание Rexroth Hagglunds CA 10






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды