manualshive.com logo in svg

Bosch Rexroth Hagglunds CA 10, Руководство по установке и обслуживанию

Поделиться
Скачать
Bosch Rexroth Hagglunds CA 10 Скачать руководство пользователя страница 50

 

Technical data

 

49/52

Bosch Rexroth Mellansel AB

,  Installation and maintenance manual, Hägglunds CA 10 - CA 40, RE 15354-WA/04.2015

Details regarding the selection of hydraulic fluid

The hydraulic fluid should be selected such that the operating viscosity in the 
temperature range, as measured in the motor housing, is within optimum operation 
range, see 

Fig. 28: Selection diagram for viscosity ranges with straight fluids, i.e. 

viscosity index 100

•  General recommendation is to have a system temperature of 50°C, see dotted 

line in Diagram 1. A VG 68 fluid  will render just above 40 cSt at this point.

•  Optimum viscosity range is 40 to 150 cSt.
•  Running above 150 cSt or below 40 cSt results in reduced efficiency.
•  Running above 400 cSt results in substantial efficiency loss.
•  Starting at above 10000 cSt imparts unnecessary strain on parts.
•  Running below 30cSt may impact the service life.
•  Running below 20 cSt may render instant seizure.

The operating temperature is also limited by the seal type, see

 Table 18: General data 

(metric)or Table 20: General data (US)

15.1.4 

 Hydraulic fluids

The hydraulic motor Hägglunds CA is primarily designed for operation with hydraulic 
fluids according to ISO 11158 HM.
Fluids by the standards given in 

Table 26: Suggested fluid types

 are suggested. Before 

the start of project planning, see data sheet  RE 15414, Hydraulic fluid quick 
reference, for detailed information on hydraulic fluids and specific additional 
demands 

SO 11158 

ISO 15380 

ISO 12922 

HM 

HEES 

HFB 

HV

HEPG

HFC 

HEPR

HFDU

Table 26: 

Suggested fluid types

Filtration of the hydraulic fluid

A contamination level of at most 18/16/13 according to ISO 4406 is required. The 

less contamined the fluid, the longer the service life of the hydraulic motor.

Содержание Rexroth Hagglunds CA 10






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды